Question about 2000 Jaguar S-Type

1 Answer

How to remove door panel to gain access w/out damaging panel?

Same problem but a rear door window. How to remove door panel to gain access w/out damaging panel?

Posted by on

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jaguar Expert
  • 489 Answers

I hope this helps , easier done than said :)
1- Remove door latch bezel. (handle) 2- You will find door trim panel retaining bolt , remove it. 3- Remove the door pull handle screw cover. 4- Remove the door pull handle retaining screws. 5- Detach the interior door trim panel ( to make removal easy , release clip by lowering glass and pressing case inwords) 6- Disconnect the door trim harness electrical connector. 7- Remove the door trim. 8- Disconnect the driver door module electrical connector 9- To install , reverse removal procedures

Posted on Aug 14, 2009

Testimonial: "Project completed. Karaman is correct with the steps needed to remove and gain access to window. Thanks"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 cadillac deville, The left rear window and lock don't work. Where is the door module location for left rear door. Any dianostic suggestions


The door module for that door is actually located inside of that door. You have to remove the door panel to gain access to it. Each door has it's own module on your car;)

Jul 31, 2011 | 2002 Cadillac Deville

1 Answer

Passger door wont open from the outside the door handle is loose


The door handle assembly may have just come loose from the door. It is attached from the inside and is accessed by removing the inner door panel. Removing inner door panels is usually not that difficult once you find out how they are attached. The first thing to do is locate any screws that are visible and remove them.(usually phillips head) I usually remove the ones along the bottom of the panel and then look for any hidden screws on the bottom of the armrest. If the door has electric windows then it might be necessary to remove the window switch to gain access to any remaining screws. Next, use a flat blade screw driver to pry the door panel away from the door. You can wrap the screwdriver with tape to avoid damage to the painted surface. The door panel is held on to the door with press fit pins which are reusable. Once the panel is removed, you should be able to repair anything that is needed.

May 16, 2011 | 1991 Chevrolet Lumina

1 Answer

Were does the LH mirror on a 2011 f-250 connect. Removed mirror but disconnect is located some were in door or body. need to know what needs to be removed to gain access


  1. Remove the front door trim panel.
  1. Position aside the front door watershield to gain access to the exterior rear view mirror control switch electrical connector.
4.Disconnect the exterior rear view mirror control switch electrical connector
ganyapr_7.jpg
as you see you have to remove the door panel to have access to the electrical connector in case that you dont know how to do it here are the instructions

NOTE: Left front door trim panel shown, right front door trim panel similar.
  1. Remove the sail panel.
    • If equipped, disconnect the electrical connector

  2. If equipped, lift up and remove the exterior rear view mirror control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, lift up and remove the window control switch panel.
    • Disconnect the electrical connector.
  1. If equipped, remove the window regulator handle.
    1. Position the window regulator handle cover aside.
    1. Remove the window regulator handle screw and regulator handle
5.Remove the door trim panel center screw cover
6.Remove the 2 door trim panel center screws
7.Remove the 2 door trim panel lower screws
  1. NOTICE: Do not pull directly outward on front door trim panel as damage will occur.
    Remove the front door trim panel.
    • Lift upward to remove the front door trim panel.
  1. NOTICE: Insert the lower panel tabs first or they can break when installing the front door trim panel.
    To install, reverse the removal procedure

Feb 20, 2011 | 2011 Ford F-250 Super Duty

1 Answer

Need to replace front door window motors


Electric Window Motor REMOVAL & INSTALLATION Ranger
  1. Disconnect the negative battery cable.
  2. Open the window. Remove the trim panel and watershield and support the window.
  3. Disconnect the power window motor connector.
  4. There may be a drill dimple in the door panel, opposite the concealed motor retaining bolt. Drill out the dimple to gain access to the bolt. Be careful to avoid damage to the wires. Remove the motor mounting bolts and remove the motor and regulator assembly.
  5. Separate the motor and drive from the regulator on a workbench.
  6. Installation is the reverse of removal.
  7. Check for smooth operation before installing the trim panel.
Except Ranger
  1. Raise the window fully if possible. If not, you will have to support the window during this procedure. Disconnect the battery ground.
  2. Remove the door trim panel.
  3. Disconnect the window motor wiring harness.
  4. There may be a drill dimple in the door panel, opposite the concealed motor retaining bolt. Drill out the dimple to gain access to the bolt. Be careful to avoid damage to the wires.
  5. Remove the motor mounting bolts (front door) or rivets(rear door).
  6. Push the motor towards the outside of the door to disengage it from the gears. You'll have to support the window glass once the motor is disengaged.
  7. Remove the motor from the door.
  8. Installation is the reverse of removal. To avoid rusting in the drilled areas, prime and paint the exposed metal, or, cover the holes with waterproof body tape. Make sure that the motor works properly before installing the trim panel.
prev.gif next.gif

Nov 12, 2010 | 1992 Ford Explorer

1 Answer

Rear right passenger window not working


Before you go to the r/r door check the wires inside the rubber boot inside the drivers door jamb chances are the wire for the rear door is broken. If I'm wrong...Undo all the visable screws and pop the covers off of the door handle area ect and lift the pannel off the door straight up towards the glass there are slots that sols the pannel on ..Good luck

Jan 12, 2010 | 2000 Buick Century

2 Answers

The driver's door window of my VW Bora has dropped inside the door panel. I need to know how to gain access and retrieve the window.


the window has detatched from the window regulator(the part that holds the glass in position and moves up and down)you need to remove the door trim to gain access to it and remove the window mechanism or manovre the glass back to the top and hold it with tape and take to a mechanic or auto elec

Oct 21, 2009 | 2000 Volkswagen Passat 4Motion

1 Answer

Power window off track


Remove the door panel and the armrest. Then you will need to slip a thin flat blade screwdriver under the panel and gently pry up to release the plastic keepers that attach the door panel. Then you can remove the panel and gain access to the window regulator and track. Be gentle prying out the plastic keepers so you don't damage the panel. Some of the keepers may break, but you can get more from Ford or your local parts house. These are a very common piece. Good luck.

Mar 06, 2009 | 2005 Ford F-150

1 Answer

How to remove REAR interior door panel 96 DeVille? Problem is to gain access to chrone window sill strip on exterior. Apparently a fastener/clip has popped off and chrome strip is sticking up on end...


Remove the power window switch module - use a 1/2" wide flat bladed tool to pry up on the rear edge. Then CAREFULLY push in to disengage the clip and pull up. Disconnect the electrical.
Remove the trim panel - there are two screws under the the covers at the ends of the door handle, and one behind the inside opener handle cover. BE VERY CAREFULL not to damage these covers.
Gently release the retainer tabs located all around the door panel, and lift up to remove..

Jul 03, 2017 | 1996 Cadillac DeVille

1 Answer

How to remove REAR interior door panel? Problem


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Feb 22, 2009 | 1995 Cadillac DeVille

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2000 Jaguar S-Type Logo

1,056 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...