Question about 1998 GMC Sierra

1 Answer

Brake peddle keeps goin farther down, less stopping. is it the calliper?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

More than likely it's air getting into the system via a leak. If you are able to, check for a brake fluid leak at the rear brakes, brake shoes should be clean, if they are oily you have a leak.

Posted on Sep 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 04 Pacifica FWD. I have a rubbing/grinding in front end. Put car on stands and let it idle in drive. Something is causing front wheels to randomly stop rotation. CV joint or tranny goin bad?


what you describe on the stands is normal differential action
rubbing /grinding noise can be bearings ,brake pads or calliper stuck on the slide pins

Jan 30, 2017 | Cars & Trucks

2 Answers

Brakes slipping


I would look for any leaks at each wheel and if no leaks master cylinder is no good.

Jan 26, 2013 | 1992 Honda Civic

1 Answer

How do i bleed the brakes on my 1984 ford mustang never done it before


same as any nother car. take off mastercylinder cap. get a helper set in the drivers seat. apply pressure to the brake peddle. with a box or tube wrench break the fluid *** on the top of the calliper/back of drum loose. foot pressure on peddle should push it to the floor -hold it on the floor! tighten the *** on the caliper/drum tight-ish. not over tight. then let peddle up off floor. pump till you get resistance/tighteness. hold pressure on peddle, loosen *** again and peddle will go to floor again tighten ***, lift up peddle pump for pressure. repeat untill all air is out of line/ or fluid runs out clear. never let the master cylinder get low on fluid. have plenty on hand. repeat for all 4 tires.

Aug 10, 2012 | 1984 Ford Mustang

2 Answers

Drive vehicle down the road for 20 minutes and come to a stoplight engine stops when you take foot off gas peddle and go to apply brake. To keep vehicle from dying you have to hold the gas peddle down


Have you changed the timing belt? or timing belt guides? How many miles? This does not necessarily have to do with fuel.... Could have to do with air intake or timing as well....

Jun 12, 2012 | 1996 Dodge Ram

2 Answers

I cant push my brake peddle down ?


sounds like the break booster or master cylinder. Also maybe a vacumm issue with the break booster make sure the line is hooked from the booster to the engine intake

Feb 02, 2011 | 1992 Ford F250

1 Answer

We replaced pads& callipers, bleed lines/ brake peddle goes to floor.brakes work but peddle still goes to floor.help!!!!!!!!!!!!


Check the vacuum hose going to the brake booster mounted on the firewall in front of the driver in the engine compartment. If that is intact and connected with no holes then the problem is the Master Cylinder.

Jan 08, 2011 | 1999 Toyota Corolla

1 Answer

I have a 2000 Dodge Durango and after bleeding the brakes (after doing some brake work) we can't seem to get the peddle to stay hard. When taking it out for a drive the first time you press on the...


Bleed them again, and don't leave the bleeder open, every time the person lets up on the pedal. close on the way down and open and close next time etc. Your letting air back into the system. Don't let the master run dry.

Sep 19, 2010 | Dodge Durango Cars & Trucks

1 Answer

Changed the front brakes and now the peddle is mushy and has to go all the way down to stop.


you have air in the system and you will need to bleed the brakes. Also it is a good idea if not essential on some cars to rotate the pistons in the callipers as you retract them or damage to the seal can occur, check you have no sign of leak!

Jan 19, 2010 | 2003 Pontiac Grand Prix

Not finding what you are looking for?
1998 GMC Sierra Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...