Question about Ford Escape

Open Question

After a battery disconnection, my '01 Escape needs to relearn its' adaptive strategy, after doing the warm-up/ air-conditioner procedure, how many miles do I have to drive until the OBD II is restored ?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the body control module located on a 2001 ford explorer


In this model year Ford calls the BCM- Generic Electronic Module (GEM) It is located , Behind center of I/P !
Module - Generic Electronic (GEM)/Central Timer (CTM) Removal
  1. syn~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result.
    Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .
  1. Remove the audio unit. For additional information, refer to Section 415-01 .
  1. Remove the center instrument panel finish panel.
    1. Remove the screws.
    1. Remove the center instrument panel finish panel.
    • Disconnect the electrical connectors.
Remove the GEM/CTM.
  1. Remove the screw.
  1. Disconnect the four connectors from the GEM/CTM.
  1. Remove the GEM/CTM.
  • Installation
    1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure

    May 16, 2016 | Ford Cars & Trucks

    1 Answer

    How do I remove the instrument cluster dimmer switch in my 2000 Lincoln town car


    Switch - Panel Dimmer
    Special Tool(s) syg~tr~en~file=st1445a.gif~gen~ref.gif Radio Removing Tool
    T87P-19061-A Removal
    1. Disconnect the battery ground cable
    2. Pull out the radio using Radio Removing Tool.
    3. Remove the radio.
      1. Disconnect the electrical connectors.
      1. Disconnect the antenna cable.
      1. Remove the radio.
      2. Remove the instrument panel finish panel bolts.
      3. Remove the instrument cluster finish panel bolts.
      4. Pull out and position aside the instrument cluster finish panel.
      5. Disconnect the electric clock electrical connector.
      6. Remove the instrument cluster finish panel.
        1. Disconnect the headlight switch electrical connector.
        1. Disconnect the dimmer switch electrical connector.
        1. Remove the instrument cluster finish panel.
        2. Remove the dimmer switch.
          1. Remove the screws.
          1. Remove the dimmer switch.
      7. Installation
        1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
          To install, reverse the removal procedure.

    Nov 29, 2015 | Lincoln Cars & Trucks

    1 Answer

    Heater cor is leaking how do I change it?


    REMOVAL




    1. Disconnect the battery ground cable.
    2. Drain the radiator. Refer to: "Engine, Cooling and Exhaust : Cooling System : Service and Repair" See: Service and Repair
    3. Remove the instrument panel. Refer to: "Body and Frame : Interior Trim : Dash Board : Service and Repair" See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair




    1. Compress the holding tabs and disconnect the heater water hoses at the heater core.




    1. Remove the A/C plenum demister adapter.
    1. Remove the screw.
    2. Remove the A/C plenum demister adapter.




    1. Disconnect the vacuum line.




    1. Remove the heater core bracket.
    1. Remove the two screws.
    2. Remove the bracket.




    8 Remove the plenum assembly top.
    1. Remove the 13 screws.
    2. Remove the plenum assembly top.
    1. Remove the blend door assembly from the case.




    1. Remove the heater core.
    INSTALLATION








    1. To install, reverse the removal procedure.
    NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

    Dec 17, 2012 | 1997 Ford Expedition

    1 Answer

    Need simple instructions on installing alternator in 98 ford escort


    SECTION 414-02: Generator and Regulator 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/05/1998 Generator-Sedan and Wagon Removal
    1. Disconnect the battery ground cable.

    1. Remove the generator drive belt.
      1. Release the tension on the drive belt.
      1. Remove the drive belt from the generator pulley.
    1. Disconnect the HO2 sensor harness clip from the generator bracket.
    1. Position the generator bracket aside.
      1. Remove the A/C line bracket bolt.
      1. Remove the power steering pressure line bracket bolts.
      1. Remove the generator bracket bolts.
      1. Position the generator bracket aside.
    2. gj1399b.gif
    1. Remove the generator bolts and position the generator aside.ddll111_14.gif
    1. Remove the generator.
      1. Disconnect the two generator electrical connectors.
      1. Remove the battery positive nut and washer.
      1. Disconnect the battery positive cable and remove the generator.ddll111_16.gif
    Installation
    1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure.

    2010&c18=modelyear&c20=n41406&c35=wsm%2cgenerator%u2014sedan%20and%20wagon%2cswf%2c414-02%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe]

    Mar 10, 2011 | Ford Escort Cars & Trucks

    1 Answer

    How do I change an alternator on a 1998 Ford Escort ZX2?


    Removal
    1. Disconnect the battery ground cable (14301).
      gl1539a.gif
    1. Remove the (A) six bolts and remove the (B) RH splash shields.
      gg0133a.gif
    1. Remove the drive belt (8620) ; refer to Section 303-05.
    1. Remove the coolant tank reservoir; refer to Section 303-03.
    1. Disconnect the two electrical connectors.
      gj0862a.gif
    1. Remove the generator bolts and position the generator (GEN) (10300) aside.
      gj0863a.gif
    1. Remove the generator.
      1. Remove the battery power nut and washer.
      1. Disconnect the battery positive cable and remove the generator.
      gj0864a.gif
    Installation
    1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure.
      gj0865b.gif
      gj0866a.gif

    Mar 07, 2011 | Ford Escort Cars & Trucks

    1 Answer

    Car not starting... Seems like battery isnt charging due to faulty alternator


    did you have alternator and battery tested Disconnect the battery ground cable.

    Remove the generator drive belt.
    Release the tension on the drive belt.
    Remove the drive belt from the generator pulley.

    Disconnect the HO2 sensor harness clip from the generator bracket.

    Position the generator bracket aside.
    Remove the A/C line bracket bolt.
    Remove the power steering pressure line bracket bolts.
    Remove the generator bracket bolts.
    Position the generator bracket aside.

    Remove the generator bolts and position the generator aside.

    Remove the generator.
    Disconnect the two generator electrical connectors.
    Remove the battery positive nut and washer.
    Disconnect the battery positive cable and remove the generator.

    Installation

    NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

    To install, reverse the removal procedure.

    Dec 18, 2010 | 1998 Ford Escort

    1 Answer

    I am looking to replace the blower motor on a 2005 ford f150 4.6L V8 and i was looking for some installation instructions or tips


    Removal & Installation


    WARNING

    TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY, THE AIR BAG SYSTEM BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING ANY CLIMATE CONTROL COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY, DISCONNECT THE BATTERY-TO-STARTER CABLE AND WAIT ONE MINUTE.


    1. Remove the battery.

    2. Remove the battery tray.

    3. If equipped with air conditioning, loosen and move the suction accumulator/drier to access the blower motor. It is not necessary to discharge the refrigerant system.

    4. Disconnect the electrical hardshell connector.

    5. Remove the blower motor housing tube.

    6. Remove four screws.

    7. Remove the retaining clip.

    8. To ease removal, align the flat spot on the blower motor mounting plate with the accumulator.

    9. Remove the blower motor.
      32069_evan_g0403.gif

      Blower Motor

    10. Remove the retaining clip.

    11. Remove the blower motor wheel.

    To install:

    1. Follow the disassembly procedure in reverse order.


      NOTE

      When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.


    Oct 22, 2010 | 2005 Ford F-150

    1 Answer

    How to change light switch on 2001 mustang


    Lamp Switch—Headlamp Removal
    1. Disconnect the battery ground cable.
    1. Remove the headlamp switch knob.
      1. Pull the headlamp switch knob out.
      1. Insert a thin tool into the slot, pull and remove the headlamp switch knob.
    8c152ea.gif

    Remove the instrument panel cluster finish panel.
    • Remove the screws and remove the finish panel.
    2d039a1.gif

  • Remove the headlamp switch.
    1. Remove the screws.
    1. Remove the switch.
    1. Disconnect the electrical connectors.
  • 4cabe95.gif
  • Installation
    1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure.

  • Hope this helps.. Cobra :-)

  • Jul 20, 2010 | 2001 Ford Mustang

    1 Answer

    How do I remove the left side mirrer on my 2000 ford explorer?


    Mirror — Outside Rear View Removal
    NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.
    1. Disconnect the battery ground cable (14301).
    1. Remove the front door trim panel; refer to Section 501-05.
    1. Remove the speaker.
      1. Remove the screws.
      1. Disconnect the electrical connector.
      1. Remove the speaker.
      gk6980a.gif
    1. Remove the outside rear view mirror (17682).
      1. Disconnect the power mirror wiring clips.
      1. Remove the outside rear view mirror nuts.
      1. Remove the outside rear view mirror.
        • Feed the power mirror wiring through the opening in the front door (20124).
      gn0316a.gif
    Installation
    1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure.
      gn0317a.gif

    May 29, 2009 | 2000 Ford Explorer

    1 Answer

    Ignition turns and key warning light comes on. Its a 98 Ford Expl


    Sounds Like the Starter RELAY is Bad After Exhausting All other Test, Go For The RELAY
    A SURE-SHOT way Is to Jumper Wire From Battery to (STARTER SIDE) of Relay if starter Works then Its the Starter Relay if NOT>>Then Its the STARTER<) Relay Instruction Below. STARTER Instructions Very Bottom
    REMOVAL
    WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE.

    1. Disconnect the battery ground cable.
      1. Disconnect the starter motor solenoid relay switch wiring.
      1. Remove the protective cover.
      2. Disconnect the push-on electrical connector.
      3. Remove the nuts.
      4. Remove the cable.
        1. Remove the starter motor solenoid relay switch.
        1. Remove the engine sensor/generator wires.
        2. Remove the bolts and ground wire.
        3. Remove the starter motor solenoid relay switch.
        INSTALLATION
      5. Follow the removal procedure in reverse order NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.
    REMOVAL

    WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE WHEN MAINTENANCE IS COMPLETED.

    1. Disconnect the battery ground cable.
    2. Raise and support the vehicle.
    3. Remove the starter motor solenoid terminal cover.
      1. Disconnect the starter wires.
      1. Remove the nuts.
      2. Disconnect the wires.Remove the nut and the starter ground cable
      3. Remove the bolt and the starter motor.
        1. Follow the removal procedure in reverse order. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

    Feb 08, 2009 | 1998 Ford Explorer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    70 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...