Question about 2000 Ford Windstar

1 Answer

Fuse number 10 continues to blow out, even after replacing twice.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

Check whatever fuse number ten locates to then check the wiring eg frount headlight check that wires are good and connectors are sound etc

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have replaced the #17 fuse (20 amp) numerous times and the cig. lighter twice


Try disconnecting the cigar lighter altogether to see if the fuse continues to blow. If it keeps blowing, you have a short somewhere in the wiring, if not the lighter is causing the problems.

May 03, 2016 | Cars & Trucks

1 Answer

Number 13 fuse blows what could be the problemn


go to the audi world blog and search fuses, the is a pdf, you will have to sign in

Jan 20, 2015 | 2007 Audi Q7 4.2 FSI

1 Answer

Vito 2006 109cdi. fuse number 41 is blowing (engine fuse)


engine light stays on
the ecu will have fault codes stored to be read
that will point to the cause and a fix of the over load

my best information on a vito if diesel..says
10 amp fuse 41 . glow plugs


you must need the van on the road very badly
30 amp in a 10 amp fuse position can
melt the wiring even a fire


index-ldszvhuomwkbtubxskurqnxk-1-0.jpg

Apr 06, 2017 | Cars & Trucks

2 Answers

Fuel pump fuse blows as soon as i turn key 1988 buick skylark 3 litre


OK, R U REPLACING THE SAME FUSE WITH THE OLD ONE U TOOK OUT IT NEED TO BE MATCHING THE SAME NUMBER

Jun 19, 2012 | Buick Skylark Cars & Trucks

1 Answer

I have a lhs 1996 Chrysler. The car wont start and the engine fuze burns out.


I also have a 96 LHS that randomly blows the 20 amp ECM fuse. If this is what you are referring to, the problem may be in one of your ECM sensors. 1-Start by unplugging all ECM sensors (Temp, Cam, Crank, 2-O2, TPS, etc.) and replace the fuse. 2-Crank the starter (the car will not start) and see if the fuse blows. If it does you probably have an electrical problem with the ECM. 2-If the fuse does not blow, plug in only the cam sensor and start the car; it will idle rough and the check engine light will come on. If the fuse blows, the problem is the cam sensor or wiring to it. 3-Continue plugging in sensors one at a time and try starting. When the fuse blows, you will know which sensor and/or wiring to the sensor to check. This process of elimination has worked twice for me.

May 16, 2010 | Cars & Trucks

1 Answer

Engine management fuse keeps blowing


My car stopped running without any warning, its a 2005 ford focus, 2.0 and the 20 amp fuse for the engine management keeps blowing, it's number 9 in the panel and I have replaced it twice, both times it blew again, any tips? Also the odometer reads ------ and that's it.

Jan 09, 2010 | 2001 Ford Focus

1 Answer

Fuse for trailer right turn signal and brake blows intermittently


abad ground on that tail light unit could affect current load when turn and stop are used simultaneously. Although one side only is affected make sure of good grnd between trailer and tow vehicle. focust on the tail light unit in question. Replace the bulb. though rare, bulbs have been known to be the problem. If the bulb is breaking filiments ck the filiment orientation. filiments last longer in vertical orientation, where horizontal permits vibration to break the heated filiment when brake is applied.. good luck and let me know if This helped or not.

Apr 26, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

Blowing fuel pump fuse


Did you change the pump? It may be drawing too much current and causing the fuse to blow... My recommendation is to replace that if you continue to have this problem OR unplug the fuel pump and see if it still blows... then it is a shorted wire!

Apr 19, 2009 | 1997 Pontiac Sunfire

1 Answer

Igniton fuse continuously blows on my 1995-96 dodge neon


Do you have an aftermarket stereo installed? Well, try this. Remove the ground cable from the battery. Install a new fuse. if it continues, Remove the center console. and check the reverse wire connected to the shifter. It did the same thing to me and all it was, was that wire was touching other wires

Jan 11, 2009 | 1995 Dodge Neon

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...