Question about 2004 Nissan 350Z

Open Question

Torque setting for Seat Leon wheel nuts - 2004 Nissan 350Z

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for a front wheel bearing?


if its not a drive axle and only has a castle nut with a cotter pin , then regrease the wheel bearings and run nut all the way in to its hand wrench tight (not impact gun), turn wheel one or two full turns to seat it , then back castle nut off two spaces and install cotter pin , this s\is std way to set proper spacing on wheel bearings

if its a drive axle consult your cars model and make and year torque specs book

Mar 29, 2016 | Cars & Trucks

1 Answer

Torque setting for wheel nuts on Renault Alloy wheels


130(NM) 96 ft/lbs is the torque setting for a 2008 renault scenic so as not to ruin studs or brake rotors should be sufficient for allloys just need to check alloy lug nuts more often

Aug 09, 2014 | Renault SCENIC Cars & Trucks

2 Answers

What is the torque setting for my alloy wheels?


Your torque spec is usually based off of lug diameter, if you have 19mm lug nuts then 75#ft should be sufficient.

Aug 09, 2014 | 2007 Renault Scenic 1.5

2 Answers

Lug nut torque chart


Here's a handy link to the wheel nut torque settings for hundreds of different vehicles.
Look your's up........and away you go!
http://www.discounttiredirect.com/infoCenter/infoWheelTorque.html

Jul 30, 2014 | 2004 Pontiac Montana

1 Answer

Replacing axel on passenger side of 2000 hyundai elantra please give a step by step


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Front wheel
    • Spindle nut
    • Wheel speed sensor, if equipped
    • Outer tie rod end
    • Stabilizer bar link
    • Lower ball joint
  3. Press the stub shaft out of the hub.
  4. Pry the inner joint out of the transaxle or intermediate shaft.

To install:

NOTE

Use new circlips, split pins and self-locking nuts for assembly.


  1. Install the inner joint so that the circlip is felt to seat in the retaining groove.
  2. Guide the stub shaft into the hub.
  3. Install or connect the following:
    • Lower ball joint and torque the nut to 43-52 ft. lbs. (58-70 Nm)
    • Stabilizer bar link
    • Outer tie rod end and torque the nut to 17-25 ft. lbs. (23-34 Nm)
    • Wheel speed sensor, if equipped
    • Spindle nut and torque the nut to 144-187 ft. lbs. (195-253 Nm)
    • Front wheel
  4. Check and/or adjust the wheel alignment.

Jun 16, 2011 | 2000 Hyundai Elantra

1 Answer

TORQUE SETTINGS FOR 1.4 16V 04 VAG ENGINE THEY USED IN SEAT LEON 04 16V 1.4.


Cylinder head instructions

Tightening sequence
tdisline_536.jpg
Cylinder head torque setting for 2004 VW 1.4L 16V fitted in Seat Leon
Renew bolts

Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

May 17, 2011 | 2000 Volkswagen Golf

2 Answers

I just did the wheel bearings on my 1985 ford f 150 2 wd i need to find out what the torque is for the nut that holds my wheel bearings and brake rotor on thank you very much


  • There is not a torque speck for that.

  1. Just thread the adjuster into the spindle and tighten real good with a ratchet.
  2. Then rotate the wheel forward to seat them bearings real good.
  3. Give it another tighten then back that adjuster nut off 1/8 of a turn.
  4. Then put the nut lock washer on over the adjuster nut and put a cotter pin in the hole.


  • Your lug nuts are torqued at 100ft lbs though.


Regards, Tony

Apr 28, 2011 | Ford F-150 Cars & Trucks

1 Answer

I am looking for the factory torque settings for the front wheel bearings for a 2004 Chevy s10 pick up.


IF YOU HAVE 4WD YOU WILL HAVE TO REPLACE BEARINGS.NOT ADJUSTABLE. IF YOU HAVE A 2WD YOU WILL REMOVE COTTER PIN AND LOOSEN THE SPINDLE NUT.SPIN THE WHEEL FORWARD BY HAND THE TORQUE NUT TO 12 FT LBS TO SEAT BEARING.THEN BACK OFF NUT 1/4 TO 1/2 TURN TO UNTIL HOLE IN SPINDLE LINE UP WITH SLOT IN NUT.THEN INSTALL A NEW COTTER PIN.

Sep 11, 2009 | 2004 Chevrolet S-10

1 Answer

Wheel nut torque wrench settings for Seat Toledo V5 November 2001 model.


14mm bolt 100 ft lbs 12mm bolt 80 ft lbs. if you drive real fast on 14mm bolt I like 120ft lbs

Apr 24, 2009 | 2001 Volkswagen Golf

2 Answers

Torque Setting for the Wheel Berring Nut


Is this a 4x4 or 2 wheel drive?If its 4x4 its 150flbs and 2 wheel drive its tightened by hand until slop or wobble is gone.

Mar 30, 2009 | 1999 GMC Yukon

Not finding what you are looking for?
2004 Nissan 350Z Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...