Question about 1995 Ford Explorer

1 Answer

Is there a inline fuse from the ignition switch to the ignition coil?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 321 Answers

No sir
not from the switch to the coil.
the coil does not get power from the switch.
the switch turns relays on that powers the coils.
but there is an ignition fuse.
the ignition switch turns on power relays from the battery that powers the ignition system.
the ignition system fuse is in the fuse box.

hope this helps
thank you
jm

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No start no power to ignition coil tested high current fuse panel no power there either 1994 ford Taurus 3.8 fuel injected


Ignition switch supply's B+ voltage to ignition coil fuse in the engine compartment fuse box , 10 amp fuse . If no B+ voltage there check ignition switch .

Dec 16, 2015 | Ford Cars & Trucks

2 Answers

Could I run a electric fuel pump on my 1998 Cadillac deville?


if it did not have an electric fuel before then the installation of an electric pump is a relatively easy process. If you have an electric pump already fitted but it has failed then remove it and install the new pump in its place. Take care to check all wires, fuses and relays and any pressure sensors for correct operation. Remove and blank of the opening for any mechanical pump on the engine
For new installation select an easily accessible place under the vehicle that can be protected from flying rocks and road debris. Run a power wire (red colour) from the run side of the ignition switch to the relay ( to be fitted ) near the battery or in the engine bay. Run this wire through an inline fuse close to the ignition switch to protect the circuit. attach to a coil actuation terminal of the relay.( look at the base of the relay for terminal identification. Run a black wire from the other side of the coil actuation pin on the relay to earth. Normally the same bolt that mounts the relay. Run a red wire capable of carrying 20 amps directly from the battery terminal through an inline fuse ( close to the terminal) to a power pin on the relay. Run another red wire from the outlet power pin on the relay to the electric pump. . Run an earth wire from the pump to earth.
This is a basic electric circuit for the installation of the pump. If there is a requirement for a pressure regulator or pressure sensor to control the pressure or pump operation , that control wire will be connected in series into the wire from the ignition switch so that when the pressure is reached then it breaks the circuit to the relay from the ign. switch and the pump will stop operation until the circuit is again completed. When the ignition switch is off there will be no power for the pump

Oct 09, 2014 | 1998 Cadillac DeVille

1 Answer

Calibre thermo fan wiring diagram


never ever wire to the ignition or other EFI parts
no car model stated, no year, and no engine option type, size etc.
A SUZUK, something...
the cooling fan wires to ground and power via a thermostatic switch
best is to wire it to IGN1, feed at the ignition key .
using an inline fuse.rated for you r fan draw.
if you trust that new switch (id not) some wire it to the battery
but if it sticks on , it will drain the battery.

post car spec. what car, so i can tell you exact wire location.

Jan 18, 2014 | Suzuki Cars & Trucks

1 Answer

89 Comanche 4.0 inline 6cyl no power to pump and now no spark as well?


I'll try to help you, John.
For spark: If your spark plugs, spark plug wires, dist. cap, and rotor are good, check the coil. Take off the negative battery cable. Use an ohmmeter and check resistance between the coil primary positive terminal and the frame of the coil-ohmmeter should show infinite resistance, if not, replace coil. Put ohmmeter positive lead on coil primary positive terminal, and ohmmeter negative lead on coil primary negative terminal-resistance should be zero or nearly zero, if not, replace coil. Connect ohmmeter negative lead to the negative primary terminal and ohmmeter positive lead to the high voltage terminal of the coil. Ohmmeter should not show infinite resistance, if it does, replace coil.
If coil is good (or has been swapped), check that coil primary has power to it with key on. If it does, and no spark, the problem could be the ignition module or the pickup coil. The ignition module should be mounted with the ignition coil. The pickup coil is inside the distributor-this pickup coil is what tells the computer (ecu) the crankshaft position, so is critical for spark timing.

For the pump: the fuel pump relay is in the power distribution box under the hood. When the ignition switch's run wire energizes the relay's coil, power is sent to the pump. You could check for a signal on the pump wire at the tank, with the engine cranking Should be a steady signal then. If not, pull the relay out to check that the power feed for the pump is still there. The power to the relay comes from Fuse link G, a 20 amp rated green fuse link. It is hot at all times, so check for a power signal on one of the relay terminals with key off. One terminal should have power. If not, check fuse link G. If it does have power, put relay back in and have someone cycle the key-relay should click-may feel or hear it. If nothing, try a different relay. If relay was good, but no power to pump, pull relay and check terminals that relay plugs into: with key held in crank, two terminals at relay should have power-the power feed from fuse link G, and now the ignition switch signal to the relay coil side. If all checks out, probably a bad pump. If you checked for power at the tank with the engine cranking, and did have power, that is for sure a pump that needs replacing.
Good luck.

Sep 06, 2013 | Cars & Trucks

1 Answer

Ignition wire to coil has no power. Jump wire from battery to coil allows it to run, like normal..


On your fire wall where the wires come out of the truck you will have what is called an inline fuse. It is gone and there is no way to replace it. It will be black in color and should be on a orange wire. It is about an inch in leangth. Cut it out and put a new inline fuse you can buy at ya auto parts store for around 5 bucks. It should have a 20amp fuse to it. This should take care of ya troubles.

Dec 01, 2012 | Ford F-150 Cars & Trucks

1 Answer

I have a 78 dodge pickup,for a derby truck, with 360,need to know how to wire ignition to simplest form,want to put in push button with on off switch,i know it can be done just not sure how,its stock...


Hello peterrole1 ,

The easiest way I can think of is to switch the power to the coil. Put a switch inline on the positive side of the coil. When it's off no power to the coil when on the power is restored.

Regards,
netvan

Mar 11, 2011 | 1983 Dodge Pickup

2 Answers

I have no supply voltage to the coil in my Ford 1988 F250. I have changed the ignition switch and tested the wiring harness. Both have proven not to be the problem. What should I do next? Help?? ...


Hi if you have power supply from the ignition switch to the coil then there is a problem from the switch to the coil. It may have a fusible wire inline with it which maybe broken. The next best thing to do is run a wire from the ignition switch to the coil this will get it going.

Jan 24, 2011 | Ford F-250 Cars & Trucks

1 Answer

I would like to put an ignition kill switch in my 2005 express van. Which wire do i cut into?


It may be better to remove the blade style ignition fuse and use a switch with inline fuse, two wires with male spade connectors to connect the two open fuse terminals.

Feb 21, 2010 | 2005 Chevrolet Express

Not finding what you are looking for?
1995 Ford Explorer Logo

Related Topics:

565 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...