Question about 1991 Toyota Pickup

1 Answer

No power to reverse lights - 1991 Toyota Pickup

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 39 Answers

Check bulbs, and fuse, then relay switch, then good luck.

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reverse light and backing camera is not working. Might it be a fuse folt?? where could I find it?


check light bulbs are ok in reverse lights. Check wiring to reverse lights - see if they put a fuse at or near where they tapped power off reverse light.

Mar 07, 2016 | 2009 Nissan Murano

1 Answer

Reverse light not working what to do


If bulbs are good then you need to check the switch that powers them when you put the car into reverse.

FYI - Neutral safety switch prevents car from starting unless it is in neutral transmission position only.

Oct 05, 2015 | Cars & Trucks

1 Answer

How to fit a g427 gator reversing camera to a vy commodore. Confused to what wire to connect for the power to the monitor,and where that wire would be located.thanks Dale


The main active / positive you can pick up direct from a connection under the dash or from the fuse box. Its easy if you have a 12volt test light, you can locate a permanent or switched 12 volt when the ignition key is on. The viewer is usually always on when the ignition is on. The camera picks up power direct from the reversing light. Use a crimp connector or solder direct to the terminal which supplies power to the reverse lights. That way the only time the camera will operate is when the reverse lights are on. The tail and reversing lights usually have a common neutral or negative wire which is connected to the body of the car. The other wire is the one you want. That's the active wire that supplies power when reverse is selected.

Jan 02, 2015 | Cars & Trucks

1 Answer

Reverse lights don't work on a 2007 chevy aveo


Check reverse light circuit, possible switch on transmission or burned-out bulbs. Is there power to the bulb socket when the key is on and trans in reverse? Use a test light to check for power at the connector.

Apr 22, 2014 | 2007 Chevrolet Aveo Sedan

2 Answers

Reverse lights/Rear internal brake light not working


there is a reverse switch on top of the trans where the shift cable is attached. is there power to and through that switch while in reverse? the cyclops light needs the power interruption traced back from the socket to the switch on the brake pedal to find out where you have lost power or possibly taped into brake power at another brake light bulb socket

Mar 31, 2014 | 1988 Toyota Camry

1 Answer

Reverse lights have no power


There's a reverse light switch somewhere. Commonly found on the transmission, but could be elsewhere in the Jeep. There's also likely a fuse as well.

Mar 01, 2014 | 1998 Jeep Cherokee

1 Answer

Reverse lights not working


sounds like cable is broken in side temporary run a cable from fuse to reverse-switch.. then check out if ok run new cable from fuse to switch

Oct 05, 2013 | BMW 525 Cars & Trucks

2 Answers

Reverse light dont work


No they should only come on when you put in reverse or else everyone would think you were backing up! its your bulb if just one, the fuse if both or the reverse switch indicator... Good Luck

Jan 21, 2013 | 2003 Chevrolet Tracker

1 Answer

2005 Pathfinder no reverse lights


On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Apr 20, 2009 | 2005 Nissan Pathfinder

Not finding what you are looking for?
1991 Toyota Pickup Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...