Question about 1995 Mitsubishi Montero

2 Answers

After a short driver water comes out expansion tank

Engine over heating

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

You may have a thermostate stock in the close position or a failed water pump check condition of both starting with thermostate good idea to change radiator cap and service radiator

Posted on Aug 07, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 62 Answers

CHECK WATER LEVEL CHECK OIL LEVEL IF NO WATER FILL UP AND IF WATER DISSAPERS OR TURNS MILKY YOU HAVE A HEAD GASKET PROB CHECK WHILE RUNNING BUT DONT GET TOO HOT

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 BMW 525i 2.5L engine overheats after rplaceing water pump, stermostat,fan clucth,radiator


There's trapped air in the cooling system.
  • You need to remove the bleeder screw on top of the radiator when adding water to the expansion tank.
  • With the engine running, pour water into the expansion tank till you see air go out through the bleeder screw's hole.
  • Just keep adding water until no more air bubbles come out then just put the screw back in place.
  • Then fill the expansion tank to it's normal level/line.

1990-bmw-525i-2-5l-engine-overheats-fibacwft50qlopemjcsdtpdf-4-0.jpg

1990-bmw-525i-2-5l-engine-overheats-fibacwft50qlopemjcsdtpdf-4-5.jpg

May 07, 2014 | 1990 BMW 525i

1 Answer

2000 vw beetle 2.0 L, low level coolant light...engine mil code 1256


not the pump but air in the system or a broken wire to the coolant level sensor
that sensor at the top of the radiator tank has to be completely immersed in coolant or the circuit is broken and the light comes on
same effect id the wire to that sensor is broken in the insulation

Jun 16, 2017 | Cars & Trucks

2 Answers

My temp gauge goes to the third line before fans come on and only the low fan comes on. I already replaced thermostat, engine coolant temp. sensor and radiator flush... any idea why high fans dont come on...


CHECK COOLANT FAN FUSES AND RELAYS. CHECK COOLANT LEVEL.MAKE SURE ITS NOT TOO LOW BECAUSE IF COOLANT TOO LOW . BY NO COOLANT AROUND OR COOLANT SENSOR NOT SUBMERGED IN COOLANT COOLING FANS WONT TURN ON.MAKE SURE YOU HAVE 50/50 ANTIFREEZE AND WATER. CHECK FOR CLAPSE RADIATOR HOSES.CHECK RADIATOR HOSE AT WATER PUMP.IF HOSE LOOK CLAPSE REPLACE IT AND BLEED COOLANT SYSTEM.IF EVERY THING HAS BEEN DONE YOU NEED ENGINE BLOCK FLUSHED OUT.HEATER CORE ALSO COULD BE STOPPED UP.A VERY HIGH MILEAGE ENGINE WILL OVER HEAT.OLD ENGINE LOSES COMPRESSION AND HORSE POWER.PUTTING MORE LOAD ON THE OLD ENGINE WILL MAKE IT OVER HEAT.IF COOLANT LEVEL IS LOW.BLEED COOLANT SYSTEM.START THE ENGINE LET IT IDLE FEW MINUTES WATCH THE COOLANT TEMPERATURE GAUGE.WHEN TEMPERATURE START RISING.TURN OFF THE ENGINE LET IT SET FOR 20 MINUTES.TAKE A LARGE RAG PLACE OVER RADIATOR CAP ON COOLANT EXPANSION TANK SLOWLY OPEN RADIATOR CAP JUST A LITTLE TO RELEASE A LITTLE PRESSURE AT A TIME.DONT OPEN CAP RAPIDLY OR YOU WILL GET SCALDED.ONCE THE RADIATOR CAP REMOVED.IF COOLANT LOW ADD MORE COOLANT IN THE THE COOLANT EXPANSION UNTIL YOU GET TO THE COLD MARK.REPEAT THIS PROCEDURE START ENGINE LET IT RUN UNTIL TEMP GAUGE START CLIMBING A BIT DONT LET CAR RUN TO OVER HEAT JUST IDLE UNTIL TEMP JUST START TO RISE.THEN YOU TURN OFF ENGINE. WAIT 20 MINUTES.THEN USE LARGE RAG OPEN RADIATOR CAP LITTLE AT A TIME. DO THIS PROCEDURE UNTIL THE COOLANT IN THE EXPANSION TANK STOP DROPPING. THEN ALL THE AIR IS BLEED OUT THE COOLANT.WHEN COOLANT LEVEL STOP DROPPING, WHEN YOU DRIVE CAR AROUND.AND TURN OFF ENGINE.WHEN ENGINE OFF CAR SET FOR A WHILE KEEP CHECK ON THE COOLANT LEVEL IN COOLANT EXPANSION TANK. THE COOLANT LEVEL SHOULD BE AT THE COLD MARK IN THE EXPANSION TANK.MAKE SURE COOLANT IS IN THE EXPANSION TANK.IF NOT AIR WILL DRAW IN COOLANT SYSTEM. CAUSING ENGINE TO OVER HEAT.IF BLEEDING AIR OUT THE COOLANT SYSTEM DONT HELP AND COOLANT FANS DONT TURN ON YOU HAVE PCM PROBLEMS.

Apr 22, 2011 | 2004 Pontiac Grand Prix

1 Answer

How do i put coolant in a polo 1.4 year 2000


open radiator and fill the radiator. open expasion tank and fill it to the FULL mark.
start the engine with the radiator cap off. keep topping the radiator up as the air comes through the system and the level goes down. keep it FULL. top up the expansion tank if necessary back to the full mark, do not fill it to the top you will only get coolant all over your engine bay!
gently rev the engine for 20 seconds just to send the water round and get some air out of the system. top up both radiator and tank again if required. refit the radiator cap and expansion tank cap. go for short drive. check the levels again (be careful with the radiator cap since the coolant will be hot now!) - should be settled now.

ready for the road!

Jan 16, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Water come out from Water line when Engine Shutdown.


Does it show signs of over heating at all? When cool, take off rad cap & check level in rad & top it up. If down a lot, start engine, turn on heat & let run until you hear rad fan come on & check temperature gauge to see if normal operating temperature. Let it come on a couple of times, and top up rad an inch or so from top, then put rad cap back on. Top up bottle to proper level & try it. If it spits back into return bottle, try replacing rad cap.

Jun 06, 2009 | 2003 Ford Taurus

1 Answer

Water leaking from top of expansion tank.


have you replaced the bleeder screws? and the expansion tank cap they both have O-rings that compress and will fail over time also check the hose at the top of the exp tank it also has o-rings inside it

Apr 03, 2009 | 2000 BMW 3 Series

1 Answer

Water leak from top of expansion tank.2000 BMW 316i se


The water (coolant) in the expansion tank will rise and fall with the engine temperature. What the expansion tank does is collect and return coolant to and from the engine. When the engine warms up the coolant gets hot, builds up pressure and opens up the radiator cap. The coolant then goes into the expansion tank. Now when the engine cools down the pressure drops in the cooling system and the pressure drop (vacuum) pulls the coolant back into the engine via the radiator cap. The radiator cap allows the cooling system to build up pressure and by doing so increases the boiling point of the coolant, but when that pressure exceeds the caps rating the cap opens and the coolant goes to the expansion valve. The cap has another part to it that when the engine cools down and a partial vacuum is created in the cooling system a "valve" in the radiator cap opens and allows the coolant to be drawn back into the engine. I would look at your radiator cap to see if any gunk or build up is on it, and check the rubber gaskets for cracks. It's easiest just to replace the cap because they are inexpensive and easy to replace (2-10 dollars). The expansion tank should have two hoses on it. The one on the bottom comes from the radiator and the one on the top (possibly part of filler cap) runs down and is open to the ground. That way if it is overfilled or becomes overfilled it will slowly leak onto the ground. When and if you change your radiator cap, make sure the engine is cooled down, remove cap and start engine and turn heater to full blast, full heat. Leave the cap off and let it run until engine warmed up. This should burp out any air pockets that may have happened when coolant was changed. Also top off the coolant in the radiator while it is running. Hope this helps and good luck

Apr 03, 2009 | 1992 BMW 3 Series

1 Answer

Overheated motor


Hi
Have you replaced the radiator cap and if you have a expansion tank fitted check that also. As the water temp rises to normal temp it send water to the expansion tank and when it cools down it sucks it back. Check that you have the right cap on radiator it should have a return valve in the middle on the inside. The expansion tank must a solid cap.
Worth the try
Billie

Nov 10, 2008 | 1994 Toyota Corolla

1 Answer

Heating system


sonds like air in your pipes!!! run ya engine with the lid off your expansion tank and put your heater on low until water starts bubbling and may start going down in your expansion tank and if so keep topn up to max mark!!!

Oct 15, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
1995 Mitsubishi Montero Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...