Question about Hyundai Motor 2004 Sonata

Open Question

Is camshaft position sensor replacement covered by standard warranty.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a camshaft sensor


2006 Saturn Ion Camshaft position sensor location:
The camshaft position sensor is located in the top left side of the valve cover.

Feb 10, 2015 | 2006 Saturn ION

1 Answer

Where is the camshaft position sensor located in a


The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Oct 10, 2014 | Cars & Trucks

2 Answers

P1345


With your code reader, clear the codes and check they stay gone.

Aug 15, 2017 | Cars & Trucks

2 Answers

How do I replace the CAM sensor on a 1996 dodge neon?


Hi, my name is John I will do my best to assist you.

To Remove
  1. Disconnect the negative battery cable.
  2. Disconnect the filtered air tube from the throttle body and air cleaner housing.
  3. For SOHC engines, remove the air cleaner inlet tube.
  4. For SOHC engines, detach the electrical connectors from the engine coolant sensor and the camshaft position sensor.
  5. For DOHC engines, unplug the electrical connector from the camshaft position sensor.
  6. For SOHC engines, remove the brake booster hose and the electrical connectors form the holders on the end of the cylinder head cover.
  7. Unfasten the camshaft position sensor mounting screws, then remove the sensor.
  8. Loosen the screw/bolt attaching the target magnet to the rear of the camshaft.
To Install: NOTE: The target magnet has 2 locating dowels which fit into the machined locating holes in the end of the camshaft.

  1. Install the target magnet in the end of the camshaft. Tighten the retainer to 30 inch lbs. (3.4 Nm).
  2. Install the camshaft position sensor. Tighten the sensor mounting screws to 80 inch lbs. (9 Nm).
  3. For SOHC engines, place the brake booster hose and the electrical harness in the holders on the end of the valve cover.
  4. Attach the electrical connector(s) to the camshaft position sensor and coolant temperature sensor (if necessary).
  5. Install the air cleaner inlet tube and the filtered air tube.
  6. Connect the negative battery cable.
The camshaft position sensor is mounted to the rear of the cylinder head - SOHC engine shown


tecnovative_139.gif
Location of the camshaft position sensor - DOHC engine shown

tecnovative_140.gif

Unfasten the retaining bolt, then remove the target magnet from the rear of the camshaft - SOHC shown, DOHC similar

tecnovative_141.gif

The target magnet has 2 locating dowels for proper alignment during installation

tecnovative_142.gif

Feb 20, 2011 | 1996 Dodge Neon

1 Answer

How do you replace the camshaft position sensor on 2000 leganza?


This is covered by Daewoo under warranty. Contact DaewooUSA and they will send you instructions and warranty information. I had mine fixed under warranty in September, 2010. They paid for everything, new sensor, new wire, new fuse link.

Oct 27, 2010 | 2000 Daewoo Leganza

2 Answers

Where is the camshaft position sensor located on a 1997 Oldsmobile Cutlass Supreme 3.1 ?


Removal & Installation 3.1L Engine To Remove:
CMP sensor 93174g24.gif

  1. Disconnect the battery ground cable.
  2. Remove the power steering pump and set aside with the lines connected.
  3. Disconnect the camshaft position (CMP) sensor electrical connector.
  4. Remove the CMP mounting bolt.
  5. Remove the CMP sensor.
  6. Check the O-ring for damage and replace if necessary.
To Install:
NOTE: Lubricate the O-ring with clean engine oil.
  1. Install the camshaft position sensor.
    • Tighten the mounting bolt to 89 in lb (10 Nm).
  2. Connect the CMP sensor electrical connector.
  3. Install the power steering pump.
3.4L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor.
  3. Remove the sensor retainer bolt and carefully pull the sensor from the camshaft carrier. An O-ring seal may hold the sensor in place. Use care not to lose the O-ring.
Camshaft Position (CMP) sensor removal (3.4L (VIN X) engine) 93174g25.gif

To Install:
  1. Installation is the reverse of the removal procedure.
  2. Before installing a replacement camshaft sensor, lubricate the new O-ring with clean engine oil.
    • Tighten the bolt to 88 inch lbs. (10 Nm). Do not over-tighten.
  3. Connect the negative battery cable.
3.8L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor. Camshaft Position Sensor removal (3.8L engines) 93174g26.gif

  3. Remove the retaining screw and separate the sensor from the front cover.
To Install:
  1. Installation the sensor in the front cover.
  2. Tighten the bolt to just 44 inch lbs. (5 Nm). Do not over-tighten. Verify the electrical connector is secure.
  3. Connect the negative battery cable.
prev.gif next.gif

Aug 26, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Just wondering where the Camshaft position sensor in my 2005 Dodge Neon is as I need to replace it.


Removal & Installation 2.0L engine camshaft position sensor location chry_car_2.0_cpsloc.gif

2.4L engine camshaft position sensor location chry_car_2.4turbo_cpsloc.gif

2.0L SOHC Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Brake booster hose and electrical connector from holders on end of cylinder head cover and reposition
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
    • Sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor. Torque sensor mounting screws to 80 in. Lbs. (9 Nm)
    • Brake booster hose and electrical harness in holders on end of valve cover
    • Electrical connectors to camshaft position sensor
2.4L Turbo Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Air cleaner box
    • Plastic clip for the wiring harness from the stud on the valve cover
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose from the valve cover
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
  3. Remove sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor torque sensor mounting screws to 80 in. lbs. (9 Nm)
    • Electrical connectors to camshaft position sensor
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose to the valve cover
    • Plastic clip for the wiring harness to the stud on the valve cover
    • Air cleaner box
    • Negative battery cable
prev.gif next.gif

Aug 01, 2010 | 2005 Dodge Neon

1 Answer

Replacing Camshaft Position Sensor Guide audi a4


The camshaft position sensor is located behind timing belt cover in front of engine.Remove cover, sensor is visable in top right hand corner.Unplug, remove 2 10mm bolts.Reinstall,plug back up,reinstall cover,crank engine.

Sep 11, 2009 | 2002 Audi A4

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Cant find cam sensor in 2004 dodge stratus r/t


2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Feb 12, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
Hyundai Motor 2004 Sonata Logo

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...