Question about 2001 Chevrolet Silverado 1500

1 Answer

Remove bearings from right axle shaft tube on 2001 chevy siverado

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 54 Answers

These need to be heated up or cut off, no easy way to do it.

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Who to replace jeep liberty rearwheel bearing


no year stated.
so how'd we look that up, seeing as how that is 1st question.

ill guess for you. (posted many times this) so 1 more time.
2007 (roll dice i did)

read the FSM ? book,
read alldata.com online log in read. its there.
ok
first parts. is this your first ever axle job>? that be key fact. there.

part 7 and 8 , must be changed, not ever just one.
http://www.factorychryslerparts.com/productSearch.aspx?&ukey_make=1064&ukey_model=15529&modelYear=1997&ukey_category=0&ukey_driveline=0&ukey_trimlevel=0&ukey_modelRange=0&isOnSale=0&searchTerm=

this axles called 8-1/4 axle has locks.
see part id 56 in above link parts page.
it must be removed first. (or 2nd to last step)
so where do you get lost? at drums off or allsteps.

my guess once you see all the steps you will get service, right>?
most here do that, once reality hits. home.
my guess once the axle is out , you then ask how to get bearing off.
right?

quote
REMOVAL (fsm has photos, im too lazy to do all that here)
1. With vehicle in neutral, position vehicle on hoist.
2. Remove rear brake components.
3. Remove wheel speed sensor.
4. Remove differential housing cover and drain lubricant.
5. Rotate differential case so pinion mate shaft (1)
lock screw (4) is accessible. Remove lock screw
and pinion mate shaft from differential case.
6. Push axle shaft inward and remove axle shaft
C-lock (1) from the axle shaft (2).
7. Remove axle shaft from side gear (3) and axle
tube.

now the bearing. pull seal with seal pick. seal out.

REMOVAL
NOTE: Remove bearing with Bearing Remover
6310 and Foot 6310-9.
1. Remove axle shaft.
2. Remove axle seal with seal pick.
3. Position bearing (2) receiver (1) on axle tube.
4. Insert bearing remover Foot 6310-9 (3) through
receiver (2) and bearing (1).
5. Tighten remove nut (1) on the shaft (4) to pull bearing
into the receiver (3).

im not doing install, sorry. you can read the FSM or log in to alldata.com and read it all, with photos and tools shown.


07 axle, ive no idea what year your car is , no axle options. sorry.
there it is. with special tool to do extractions.....
25597571-wusxbqiag3ozaxyriyixilzn-4-0.jpg

Mar 21, 2015 | Jeep Cars & Trucks

1 Answer

How to replace rear axel wheel bearing and seal on 2006 jeep liberty renegade 4wd


its not just the seal.... i bet,

99% of seals that fail are , the bearing is allowing , out of spec.

moving in the axle

so when doing all that hard work ? we check this first.

do you know all cars have this book, called the FSM.

and all show you how this is done? every one.

factory service, manual,



but hark, we have them on line now.

alldata.com (15 BUCKS)



I BET PART 2 AND 3 ARE BAD HERE

http://www.factorychryslerparts.com/showAssembly.aspx?ukey_assembly=533119&ukey_product=4240348



THE REAL CD IS ABOUT $130 (instant payback first job done by you) see?



https://www.techauthority.com/en-US/Pages/Home.aspx





eg.

Removal & Installation


  1. Before servicing the vehicle, refer to the Precautions section.


  2. With vehicle in neutral, position vehicle on hoist.


  3. Remove differential housing cover and drain lubricant.


  4. Rotate differential case so pinion mate shaft lock screw is accessible. Remove lock screw and pinion mate shaft from differential case.


  5. Push axle shaft inward and remove axle shaft C-lock from the axle shaft.


  6. Remove axle shaft from side gear and axle tube.


  7. Remove axle shaft seal from axle tube with a seal pick.


To install:



  1. Remove any old sealer/burrs from axle tube.


  2. Coat new seal lip with axle lubricant and install seal with a seal driver.


  3. Lubricate bearing bore and seal lip with gear lubricant.


  4. Install axle shaft through seal, bearing and engage into side gear splines.


  5. Install C-lock in axle shaft end, then push axle shaft outward to seat C-lock in side gear.


  6. Install pinion mate shaft into differential case and through thrust washers and differential pinions.


  7. Align hole in shaft with hole in the differential case and install lock screw with Loctite on the threads. Tighten lock screw to 8 ft. lbs. (11 Nm).


  8. Install the differential cover.


  9. Install rear brake components.

Sep 06, 2014 | 2006 Jeep Liberty Renegade

1 Answer

How do you change the rear wheel bearings on a 2004 chevy express 1500 van?


Axle Shaft Bearing & Seal Removal & Installation To Remove:
  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Oct 18, 2010 | 2004 Chevrolet Express

1 Answer

2001 chevy camaro 5.7, how do i remove the rear driver axle which connects in the diff. in order to change the bearings and seal?


you need to open the dif and remove the locking nut and pinion shaft. Then push the axle in towards the center to remove the C clip thats on the axle.

Jul 24, 2010 | 2001 Chevrolet Camaro

1 Answer

How to change the rear bearings in my 1997 grand cherokee limited


YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE MAKE SURE ITS ON A SOLID LEVEL GROUND.THEN YOU REMOVE THE WHEELS THE BRAKE DRUM OR DISC.THEN YOU REMOVE THE NUTS THAT ATTACH THE OUTER SEAL RETAINER AND BRAKE BACKING PLATETO THE AXLE SHAFT TUBE.DISCARD THE NUTS.REMOVE AXLE SHAFT FROM HOUSING.WITH AN AXLE PULLER ATTACHED TO A SLIDE HAMMER.DISCARD INNER AXLE SEALPOSITION THE AXLE SHAFT IN A VISE.REMOVE THE RETAINING RING BY DRILLING A 1/4 HOLE ABOUT 3/4 OF THE WAY THROUGH THE RING. THEN USING A COLD CHISEL OVER THE HOLE.SPLIT THE RING.REMOVE THE BEARING WITH A ARBOR PRESS DISCARD THE SEAL AND REMOVE THE RETAINER PLATE.TO INSTALL - CLEAN THEN APPLY A THIN COATING OF WHEEL BEARING LUBRICANT TO THE BEARING AND SEAL CONTACT SURFACES APPLY WHEEL BEARING LUBRICANT TO THE LIPS OF THE REPLACEMENT INNER AND OUTER SEALS.INSTALL THE INNER SEAL WITH THE OPEN END OF THE SEAL FACING INWARD ENSURE IT IS COMPLETELY SEATED.INSTALL THE RETAINER PLATE AND THE OUTER SEAL ON THE SHAFT.ENSURE THE OPEN END OF THE SEAL FACES TOWARD THE AXLE SHAFT BEARING.PACK THE REPLACEMENT BEARING WITH WHEEL BEARING LUBRICANT AND POSITION ON THE AXLE SHAFT PRESS INTO PLACE.PRESS A REPLACEMENT BEARING RETAINER ON THE AXLE SHAFT AGAINST THE BEARING.INSTALL THE AXLE INTO THE AXLE TUBE.POSITION AND ALIGN THE SEAL RETAINER AND BRAKE SUPPORT PLATE AND INSTALL REPLACEMENT ATTACHING NUTS.TIGHTEN NUTS TO 32 FT LBS.INSTALL BRAKE ASSEMBLY WHEELS LOWER VECHICLE. YOU SAID REAR BEARINGS IF THIS WHAT YOU MEANT.I HOPE THIS CAN HELP.

Apr 12, 2010 | 1997 Jeep Grand Cherokee

1 Answer

2001 1500 chevy silverado rear axle removal ?


Typically, Chevy rear ends either have a bearing bolt plate or else it is a "c" lock axel. With the c lock style, you have to pull teh center inpsection cover off, and remove the pin that holds the IDLEing spyder gears.

The spyder gears are inside the carrier assembly. once the idler shaft is removed, you press the axle IN, towards the center of the vehicle, and then look in the area where the idler shaft was removed. You will see the C clip and the notch in the end of the axle.

Mar 11, 2010 | 2002 Chevrolet S-10

1 Answer

Cant get the front differential out


  1. Raise and support the front end on jackstands.
  2. Remove the right wheel.
  3. Position a drain pan under the axle.
  4. Remove the stabilizer bar.
  5. Remove the skid plate.
  6. Disconnect the right inner tie rod end at the relay rod.
  7. Remove the axle shaft flange bolts, turn the wheel to loosen the axle from the axle tube, push the axle towards the front of the truck and tie it out of the way.
  8. Unplug the indicator switch and actuator electrical connectors.
  9. Remove the drain plug and drain the fluid from the case.
  10. Remove the axle tube-to-frame mounting bolts.
  11. Remove the axle tube-to-carrier bolts.
  12. Remove the axle tube/shaft assembly. Keep the open end up.
  13. Position the axle tube, open end up, in a vise by clamping on the mounting flange.
  14. Remove the snapring, sleeve, connector and thrust washer from the shaft end.
  15. Tap out the axle shaft with a plastic mallet.
  16. Turn the tube, outer end up, and pry out the deflector and seal.
  17. Using a slide hammer and bearing remover adapter, remove the bearing.
  18. Clean all parts in a non-flammable solvent and inspect them for wear or damage. Clean off all old gasket material.

Jun 27, 2009 | 1999 Chevrolet S-10 Pickup

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Getting rear gears out of the difential case 1999 dodge durango


  1. Raise and support vehicle. Ensure that the transmission is in neutral.
  2. Remove wheel and tire assembly.
  3. Remove brake drum. Refer toBrakes, for proper procedure.
  4. Clean all foreign material from housing cover area.
  5. Loosen housing cover bolts. Drain lubricant from the housing and axle shaft tubes. Remove housing cover.
  6. Rotate differential case so that pinion mate gear shaft lock screw is accessible. Remove lock screw and pinion mate gear shaft from differential case
  7. Push axle shaft inward and remove axle shaft C - clip lock from the axle shaft
  8. Remove axle shaft. Use care to prevent damage to axle shaft bearing and seal, which will remain in axle shaft tube.
  9. Inspect axle shaft seal for leakage or damage.
  10. Inspect roller bearing contact surface on axle shaft for signs of brinelling, galling and pitting. If any of these conditions exist, the axle shaft and/or bearing and seal must be replaced

Feb 07, 2009 | 1999 Dodge Durango

1 Answer

Rear axle berrings


Tools needed- typical socket and ratchet set, Axle slide hammer, Wiz Wheel type rotary cut off tool, chisel, ball pein hammer, hydraulic press, bech vice
First you must remove the rear wheels, then you must remove the brake capiler and mounting bracket, remove the brake rotor. unbolt 4 nuts on back side of brake dust shield that hold the seal and bearing securly in place. then you must attatch the slide hammer to the axle shaft by using the vehicles lug studs and lug nuts. use the slide hammer to knock the axle shaft out of the housing. it generally takes about 10-15 hard slams before it comes loose. once axle shaft is free to come out remove the slide hammer and pull the shaft from the axle tube. place the axle shaft into a vise and use the cut off wheel to cut off the bearing spacer. cut parralell to shaft until you hear a snap sound once it snaps use the hammer to slide the spacer off the end of the shaft. next you need to cut the bearing off the shaft using a the same technique being careful not the cut the shaft or the seal retainer plate. once the bearing is off then you can slide off the old axle seal. now slide on a new axle seal, axle bearing, and bearing spacer. take assembly to a hydraulic press and press the spacer and bearing onto the shaft until it seats squarely and make sure its all the way down onto the axle shaft. lubricate bearing with gear oil. and install shaft back into axle tube making sure that the recess in the seal retainer plate lines up with the abs sensor wire. tighten all nuts evenly top off gear oil

Dec 27, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...