Question about 1995 Buick Regal

1 Answer

1993 buick cuts out power regardless of rpm

This also happens within the first 10 minutes of my drive, i will be driving 60 mph or just sitting at a stoplight and i will lose all power. i also just shift to neutral and restart but now the the problem is becoming more regular and the restart sometimes takes waiting up to 10 minutes. Any help, my mechanic cant find it as my car runs great when he has it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 321 Answers

Take out the ignition module and have it tested for free at autozone.
this is a tipical problem as the unit heats up and shuts down.
have them run the test a few times to get the unit heated up.
hope this helps
thank you
jm

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bronco is jerky while driving with a rapid loss and regain of rpm


could be anything from loss of signal from the throttle body, to emissions to the fuel system..check all 3 and look for any issues.. replace whats bad..

Jan 18, 2014 | 1990 Ford Bronco

2 Answers

Battery light flashes off and on/car stalls


check the condition and tension of the drive belt on the alternator. check for loose terminals . Check for moisture in the alternator and loose alternator terminals.

Jan 09, 2014 | 2000 Ford Taurus

1 Answer

1993 buick lesabre all power shuts off while driving


Repair the failed ground wire; located inside the cabin at the driver side rocker panel, under the carpet, near the forward edge of the driver's seat.

Apr 01, 2013 | 1995 Buick Regal

1 Answer

Drive cycle


Here is the OBD2 emission system drive cycle test procedure.
Engine coolant temp must be below 70c (158f) before starting the engine for either the first or second trip
The fuel level should be less than 1/2 full
First trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" for at least 10 seconds (not more than 5 min)
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary.
End of first trip. Turn the key off the begin the second trip.
Second trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" add four gallons of fuel
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary. I especially like the part where they want you to add four gallons of fuel. Not three gallons, not five gallons, four gallons. Gotta love those Nissan engineers. ...and of course they state that if the trace is not followed exactly (i.e. you botch the acceleration/deceleration) you have to start all over again from scratch

Feb 09, 2012 | 1996 Nissan Pickup

1 Answer

How do i do the drive cycle on a 1997 nissan pathfinder


The following drive cycle can be used as a guide to assist with re-setting monitors when a vehicle specific drive cycle cannot be located. This OBDII drive cycle begins with a cold start (coolant temperature below 122 degrees F and the coolant and air temperature sensors within 11 degrees of one another). This condition can be achieved by allowing the vehicle to "sit" overnight, and then by beginning the drive cycle the next day. Most drive cycles will be difficult to follow exactly under normal driving conditions, so the driver should exercise caution, road safety, and courtesy to others.
  1. . Start the engine. Idle the engine in drive for two and a half minutes with the A/C and rear defroster on.
  2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle.
  3. Hold at a steady speed of 55 mph for three minutes.
  4. Decelerate (coast down) to 20 mph without braking or depressing the clutch.
  5. Accelerate back to 55 to 60 mph at ¾ throttle.
  6. Hold at a steady speed of 55 to 60 mph for five minutes.
  7. Decelerate (coast down) to a stop without braking.

Sep 17, 2010 | 1997 Nissan Pathfinder

1 Answer

When driving at a steady speed (generally I drive 60 mph on hwy) driving along fine and then the tach will jump 500 rpm and then back down to the usual 2300. Can happen several times in a row for several...


I had this happen on another car and it turned out to be a loose connection on the tacho wiring. Fixing the poor connection fixed the problem.

Aug 20, 2017 | 1993 Honda Accord

1 Answer

1993 buick regal start and stall


The average life of a battery is 3 good years, regardless how BIG, or how it cost. Anything after that is a blessing. Personally, I would replace the battery ASAP, and then with a FULLY CHARGED battery. Then drive, and see if the problem still remains. Hope this helps

Apr 20, 2009 | 1993 Buick Regal

Not finding what you are looking for?
1995 Buick Regal Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...