Question about 1999 Mazda 626

1 Answer

I have a 2001 626 4-clinder with a windshield washer pump that won,t work. I don,t know where to find it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

The pump is located inside the washer fluid reservoir.it is easy to service with the plastic inner fender removed.

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer fluid wont spray


To check to see if pump is working,remove hose at windshield and turn on and see if fluid comes out,if it does then part that shoots it to windshield is clogged,a tooth pick may work to pry it loose and come out,if no fluid comes out,then pump is bad,you can check to see if pump is getting power with a meter.

May 18, 2013 | Cars & Trucks

1 Answer

2009 nissan frontier windshield washer pump won't work


Check fuse in fuse box inside vehicle,if good,then go to windshield washer pump and disconnect wiring,get meter and check if power is going to pump,if so then pump is at fault,if no power,thenwiring could be short somewhere to fuse box.Also check your washer hoses,that they are not kinked or came loose.Pump could just be loose.

Jan 04, 2013 | 2009 Nissan Frontier

1 Answer

Windshield washers won't work


it's most likely the pump that need to be replaced or the switch is broken. you can also check the fuse.

Dec 19, 2012 | 2003 Ford Expedition

1 Answer

1984 gmc vandura 3500 windshield washer -no power


it would be easier to remove the washer pump use two pieces of wire and jump it to the battery to make sure the pump even works. if you give it a direct power supply just for a moment to see if it even engages it won't hurt a thing. sure beats crawling all over the place trying to find the problem when it may be the washer motor itself

Jul 14, 2012 | Cars & Trucks

1 Answer

My windshield washer reservoir won't hold washer fluid.


The seam on the windshield fluid container is broken and leaking like crazy.

Jun 10, 2017 | 2001 Oldsmobile Intrigue

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

2 Answers

What fuse controls the windshield washer pump? on a 2001 Jeep Che


usually it's in the washer bottle which is usually in the fender well, ahrd to get to.
The fuse that controls it should be listed in your owners manual. Usually a 10 amp fuse in the fuse panel inside the car usually on the instrument panel somewhere.

Jan 09, 2009 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Mazda 626 Logo

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...