Question about Toyota Land Cruiser

1 Answer

Central locking not working on 1999 toyota amazon? Only 1 door opens Any suggestions on why it has stopped opening other doors? Many thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,071 Answers

Drivers door module is more than likely faulty

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Central locking 2005 subaru liberty stopped working on 2 doors


1. Replace battery in remote
2. Replace sensor at rhf door lock (it is inside of door)

Apr 30, 2014 | Cars & Trucks

1 Answer

Central locking system


check central locking system fuse it controls all door locks and other acessories.need go to dealership buy remote keys..

Mar 28, 2013 | 2000 Volvo S80

1 Answer

1999 FORD FOCUS 1.8TDI CENTRAL LOCKING FAULT !


your actuator is not working needs to be re place. I don't remember if it is a air or motor one but you need to open the penal on the door and have a look.If air one will be like arectengol and the motor is tin long

Mar 27, 2013 | 2000 Ford Focus

2 Answers

I but a new remote control of my toyota 4runner 1999 and i need i need direction on how to program the remote myself without me going to any dealer for me to save some money


Here are the instructions for programming the 99-02 4Runner Keyless Entry factory remotes:

1. Start with the following conditions: you are in the vehicle

a. Key is out of the ignition
b. Drive door is open ( all other doors are closed)
c. Driver door is unlocked (other door locks don't matter)

2. Insert the key into the ignition (don't turn it) and pull it out.

3. Perform these steps within 40 seconds:

a. Cycle the power locks 5 times. Use an even pace and try
to go relatively fast.

b. Close, then open the drivers door.

4. Perform these steps within 40 seconds:

a. Cycle the power locks 5 times (same as before).
b. Turn the ignition to ON then back to OFF.
c. Turn the ignition to ON then back to OFF.
d. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should cycle (automatically)
indicating successful entry into programming mode. Return to step 1
if the locks do not cycle at this point.

6. Perform these steps within 40 seconds:

a. Press the LOCK and UNLOCK buttons on the transmitter
simultaneously for 1 second.

b. Immediately after letting go of the lock and unlock buttons,
press the lock button by itself and hold for 2 seconds.
Within 3 seconds, the door locks should cycle ( LOCK then
UNLOCK) once-- indicating successful programming. If
the door locks don't cycle, or cycle twice. Repeat steps
6a and 6b--this remote has not been accepted.

c. Repeat steps 6a and 6b for EACH transmitter that will
operate the vehicle. Including any old transmitters.

7. Close the driver door.

Good Luck

Feb 28, 2011 | 1999 Toyota 4Runner

3 Answers

Toyota corolla verso 2007 . the central locking has stopped working


Toyota Corolla Verso - Central locking has just stopped responding


So you don't waste your time, here are some assumptions: -

1. When I press the key fob there is no sound of doors trying to lock/unlock and I know the key fob is fine.


Solution:


In this situation reset the alarm/locking system

Below is the procedure I followed to get the central locking working again: -

Open the passenger door, and look at the side of the dash board. There should be a triangular panel. Pull the panel off to reveal a small set of fuses(see the back of the panel for the fuse map). To power down the central locking you need to remove the Dome Light fuse, this is located top left. Second one down 7.5 amps. (if in doubt remove the top two 7.5 amp fuses I did)

When you remove the fuse(s) you will notice the interior light go out indicating you have powered down the system.

Now leave them out for at least 30 mins so any capacitors can discharge properly. (Be aware while the fuse is removed all central locking is disabled, so the other doors are open. I left the fuse(s) out over night with all the doors open but I don't recommend it, 30 mins should be fine)

After 30 mins replace the fuse(s) close all doors, and then try your key fob, hopefully you should here that satisfying locking sound.


2. When I press the key fob I hear the locking system trying to engage.

This could be a faulty door switch on any door including the boot, or there could be a dent in the inner door panel of any of the doors, usualy the rear doors due to the seat belt not retracting properly.

Solution:

Check all door switches for damage, and check inner panel for dents, just a small dent where the switch connects can be enough to not engage the switch. This will stop the central locking.

Use some kitchen roll wrapped in tape (as a makeshift pad) and tape to the inner door as a temp measure to engage the door switch. At least you can then lock the car.


Jan 04, 2011 | 2007 Toyota Corolla

1 Answer

My 1995 toyota lexen central locking works on all doors except the Driver door any ideas on where i might start looking is a full central lock replacement or just a fuse???


Mine is the opposite... driver's door works, all others are locked and can't be opened, even from inside. Suspect may be something to do with central locking...maybe needs re-booting somehow??

Dec 07, 2010 | Toyota Passenger Cars & Trucks

2 Answers

My central locking is not working properly


it is more than likely the drivers door latch assembly

Jul 21, 2009 | 1999 Audi A4

1 Answer

Power door locks missfire


TSB 08-023-03. replace the lock cylinder switches.

May 17, 2009 | 1999 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...