Display button is not working - Cars & Trucks

Please provide more details with what does and doesn't work, such as the display comes on and all the buttons seem to function properly there's just no sound, or "only the clock displays, not stations. No buttons work." Or "No display, no sound."

Ther are two types of clusters this is the most common, let me know if this doesnt work,you will be using the trip/reset button, when button is said it means the trip/ rest button this is the only button you will use.1)push and release button untilSETUP MENU HOLD RESET is display
2) press and hold button until you see SYSTEM CHECK or SYSTEM CHECK HOLD SET is displayed then release button.
3)press and release button to scroll the menu until you see HOLD RESET IF NEW OIL .
4) with hold rest if new oil displayed now push button and hold until you see OIL LIFE SET 100% displayed release button and your done. hope this helps.

Switch ignition ON. Press brake pedal. Press button [A]. RHD - 100248. LHD - 100254. Turn button [B], until the message "System Settings" is displayed. Press button [B]. Turn button [B] until the message "Service Info" is displayed. Press button [B]. The message "% left of oil quality/days to service" is displayed. Turn button [B] until the message "Reset Service Ind." is displayed. Press button [B]. The message "Are you sure? Yes or No" is displayed. Turn button [B] to select "Yes". Press button [B]. The message "service parameters updated" is displayed. Switch ignition OFF.
BUTTON B IS ROUND PUSH/TURN BUTTON
BUTTON A IS TWO DOWN FROM THIS

1. Turn off the ignition
2. Press and hold the button on the left side of the display while turning the ignition on
3. Service OIL will be displayed
4. Pull out the button on the right side of the display until the service prompt is cleared
5. The display should now read ---
6. If the above procedure does not work, outlined below is an alternative procedure:
7. With the ignition off, push the right button
8. Turn the ignition on and then pull the left button
9. This should clear the warning message --- I have a 2002 A4 Quattro. To reset that Service message, hold down the service button. That's the one with the picture of a wrench on it. While holding it down, turn on the ignition. Let go of the service button and press the "Mode" button just to the right of the service button. It should clear the display.

* This does not work in older models, like my Audi A4 /1.6, 1995. It needs the cable and the program ( e.g. VAG-COM). Even with this, clearing the code (IN1 or IN2) is quite complicated.

1. Turn key in ignition switch to position "1".
2. Press either Menu Button repeatedly until the basic kilometer or miles display is shown on the multifunction display .
3. Press the Reset/Illumination Button 3 times.
(You'll hear an audible beep and the voltage is shown on the multifunction display.)
4. Turn key in ignition switch to position "2".
5. Press the lower Display Button.
(The Service Display appears with miles remaining/exceeded etc.)
6. Press the Reset/Illumination Button 1 time.
(The Oil Type menu appears in the multifunction display.)
7. Select the engine oil grade by pressing the +/- Buttons.
(You may have only 1 option or multiple options depending on your engine.)
8. Press the upper Display Button.
9. Press the Reset/Illumination Button for 3 seconds to confirm.
10. Press the upper Display Button to return to the Service Display menu.
11. Press the upper Menu Button to display the kilometer or miles reading.
12. Turn key in ignition switch to position "0".

Please post back with any questions. Best of luck.
Greg

Use these instuctions if your Deville has an Analog Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Panel (CCP) simultaneously.
(Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode.
Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.
If “RFA DATA” is displayed, press FAN DOWN.
If “RFA OVERRIDE” is displayed, press FAN UP.
2. If “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.
If “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.
3. IPC will show “0” on right side of Driver Information Center (DIC) display.
Press warmer button on climate control unit until “99” is displayed.
4. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.
5. To program a second remote, press FAN DOWN button until “RFA 502 PROGRAM FOB #2” is displayed, then press
FAN UP. Repeat step 4.
To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.




Use these instructions if your DeVille has a Digital Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
light all telltales, go blank then enter DIAGNOSTIC MODE. Press FAN DOW button to scroll through system until
“RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
press FAN UP button. When “NO OVRD RF 500” is displayed, then press FAN UP button.
2. When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
below odometer. System is now ready to program remote.
3. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.)
4. To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
program second remote.
To exit system, press RECIRC or RESET buttons.

Disclaimer

Press the setup button until "press reset at oil change" is displayed.
Then press and Release reset button until "hold reset to confirm" is displayed.
Now press and Hold reset button until "oil life set to 100%" is displayed.

hi..make sure that u have turned on the
display button the set.once u have turned
off the display button in your set ur display
doesn't appear.This display option will be
available in the set.
check it out.
thank u.. rate me..

Turn on radio - the word SAFE will appear in the display. Press th P.SCAN and RBDS buttons simultaneously and hold them down until "1000" lights up in the display.Release buttons.Do not, under no circumtances, continue holding them down or press them once again. This will cause the radio to consider the number 1000 to be the input code.Use station buttons 1,2,3,and 4 to enter the code number on your Radio Card. Use the button 1 to enter the first number 2 for the second number 3 for the third number and 4 for the last number.Once you have entered the code and it shows on the display,press the P.SCAN and RBDS buttons down again simultaneously and hold them down until the word SAFE appears in the display.Release buttons. Soon afterwards a frequency will be displayed.