Cars & Trucks Logo

Related Topics:

Shepherd Dick Posted on Oct 16, 2017

2012 BMW X5 propeller shaft break causes? - BMW Cars & Trucks

4 Related Answers

Anonymous

  • 81 Answers
  • Posted on Mar 30, 2010

SOURCE: procedures for removing drive shaft bmw x5

no the spindle stays on the vehicle,this process is not that difficult.start by removing the wheels and 38mm nut at the end of each shaft,then reomve the bolt holding on the front lower control arm from the front sub frame,pressout the shaft through the wheel bearing,now that the end of the shaft is out use a pry bar to pop out the shaft in the oil pan,pull them out and replace, Also you must be aware that removeing the 38mm nut is difficult without a impact gun and it is also a 12 point nut as well you must force out the ends of the drive shaft with a special puller of a air chistle with a point as you are not able to push it through by hand good luck

Ad

Anonymous

  • 437 Answers
  • Posted on Jun 26, 2010

SOURCE: BMW X5 4.4i Transmission lags or slips

filter and fluid. If that doesn't do it $4000 should do it.

Jonah Oneal

  • 14092 Answers
  • Posted on Aug 12, 2010

SOURCE: how do I remove the

REMOVE FRONT WHEEL/.REMOVE THE REINFORCEMENT PLATE / REMOVE FRONT SPLASH GUARD / REMOVE ABS PULSE GENERATOR / REMOVE BRAKE CALIPER FROM DISC AND TIE OUT OF THE WAY WITH THE HOSE STILL CONNECTED / REMOVE STEERING GEAR TIE ROD FROM SWIVEL BEARING / REMOVE THE TENSION STRUT WITH GUIDE JOINT FROM SWIVEL BEARING / REMOVE THE CONTROL ARM FROM SWIVEL BEARING / REMOVE THE COLLAR NUT ON HALFSHAFT PRESS HALFSHAFT OUT OF DRIVE FLANGE / REMOVE THE HALFSHAFT.BESURE TO REPLACE THE SNAP RING ON THE HALFSHAFT.WHEN INSTALLING HALFSHAFT BESURE TO PUSH IN OUTPUT SHAFT OVER THE RESISTANCE OF THE THE RETAINING RING UNTIL IT SNAPS IN PLACE.WHEN JOB FINISHED CHECK THE FRONT AXLE DIFFERENTIAL FLUID LEVEL.

wgreebid

wobdxue

  • 36 Answers
  • Posted on Nov 29, 2013

SOURCE: what reason is caused?A BMW X5 engine oil pressure warning light

May be due to oil pump wear, filter blocked by dirt, oil filter is exposed out of the oil surface, the oil level is low, the oil mixed with air and the pressure gauge is caused by the failure of the. In addition, the oil viscosity is low, the oil seal and poor lubrication, lubricating oil viscosity is too large, too cold oil sludge deposition too much also can cause the oil pressure indicator display abnormal.
source: obd2 tool car diagnostic

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Need crank shaft cap torque specs on BMW x5 3.0i 2004

Torque for harmonic balance/ crankshaft pulley is 410nm
0helpful
2answers

2004 Bmw x5 valve cover torque specs

valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...
Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com
0helpful
1answer

Transmission failsafe mode

code po720 refers to output shaft speed sensor (OSS) --circuit malfunction ===causes---wiring---OSS sensor---TCM
code po771 refers to shift solenoid (SS0 E --performance stuck off===causes --wiring ---shift solenoid.
0helpful
1answer

2003 bmw x5 climate control doesn't have power: what would cause this?

No power to something, no matter what, normally means a blown fuse. Check the fuse to it. The fuse panel cover has the diagram on the under side of it or would be in the operator/repair manual.
Apr 14, 2013 • 2003 BMW X5
0helpful
1answer

HOW MANY MILES NEED TO REPLACED THE TIMING CHAIN ON 2004 BMW X5 3.0 I

It doesn't need to be replaced- EVER. It is a double roller chain. It will be the Last thing to break right after the wheels fall off. Seriously, its good for 300k and more. Stop worrying.

Its also extremely complicated and expensive to replace. I could see replacing if you have to repair the heads anyway, but never as preventive maintenance. This isn't a toyota or lexus that breaks after 60k miles.

Many time, people replacing this item have a high degree of difficulty doing it right. This is especially true for people with a lot of experience on other brands and no experience with BMW Vanos systems. I can't tell you how many people decided to replace the timing chain on their fully operational BMW just to see that it would never run again.
4helpful
1answer

Procedures for removing drive shaft bmw x5

no the spindle stays on the vehicle,this process is not that difficult.start by removing the wheels and 38mm nut at the end of each shaft,then reomve the bolt holding on the front lower control arm from the front sub frame,pressout the shaft through the wheel bearing,now that the end of the shaft is out use a pry bar to pop out the shaft in the oil pan,pull them out and replace, Also you must be aware that removeing the 38mm nut is difficult without a impact gun and it is also a 12 point nut as well you must force out the ends of the drive shaft with a special puller of a air chistle with a point as you are not able to push it through by hand good luck
1helpful
1answer

I have a 2000 BMW 323ci . The car is over heating and the secondary fan is not turning on. What might the problem be?

check coolant level, might be a leak. most bmws have a water pump that uses a plastic impeller/propeller (dont know the technical name), but it breaks off the water pump shaft, and no coolant is circulated through the engine and radiator
Not finding what you are looking for?

60 views

Ask a Question

Usually answered in minutes!

Top BMW Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

old marine
old marine

Level 3 Expert

2426 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...