Question about 2004 Jeep Grand Cherokee

Open Question

Windows inop locks and mirrors inop tried master switch still not working

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which Relay/Fuse controls the power windows?


Did you check for battery voltage at the switch , with a volt meter before you replaced the main driver door switch ? Maybe you'll want to take this to pro ,instead of just replacing parts !
Symptom Chart Condition Possible Sources Action
  • No communication with the smart junction box (SJB)
  • Circuitry
  • SJB
  • REFER to Section 419-10 .
  • A single power window is inoperative - driver front power window is inoperative/does not operate correctly
  • Power window motor regulator and motor
  • Circuitry
  • Window control switch
  • Smart junction box (SJB)
  • Go To Pinpoint Test A .
  • A single power window is inoperative - passenger front, left rear or right rear
  • Power window motor regulator and motor
  • Circuitry
  • Window control switch
  • Go To Pinpoint Test B .
  • All power windows are inoperative
  • Smart junction box (SJB) fuse 30 (10A)
  • SJB circuit breaker 10 (30A)
  • Circuitry
  • Delayed accessory relay
  • Battery saver relay
  • Driver window control switch
  • SJB
  • Go To
PINPOINT TEST C: ALL POWER WINDOWS ARE INOPERATIVE Test Step Result / Action to Take C1 CHECK FOR CORRECT OPERATION OF THE INTERIOR LIGHTS
  • Turn on the interior lights.
  • Do the interior lights operate normally?
Yes
GO to C2 .

No
To continue diagnosis, REFER to Section 417-02 . C2 CHECK CIRCUIT 400 (LB/BK) FOR VOLTAGE TO THE DRIVER WINDOW CONTROL SWITCH
  • Disconnect: Driver Window Control Switch C504b.
  • Key in ON position.
  • Measure the voltage between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and ground.
    >
  • Is the voltage greater than 10 volts?
Yes
GO to C4 .

No
GO to C3 . C3 CHECK CIRCUIT 400 (LB/BK) FOR AN OPEN OR SHORT TO GROUND
  • Key in OFF position.
  • Disconnect: SJB C2280c.
  • Measure the resistance between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and the SJB C2280c pin 17, circuit 400 (LB/BK), harness side; and between the driver window control switch C504b pin 4, circuit 400 (LB/BK), harness side and ground.
    >
  • Is the resistance less than 5 ohms between the driver window control switch and the SJB; and greater than 10,000 ohms between the driver window control switch and ground?
Yes
Go To Pinpoint Test H

No
REPAIR the circuit. TEST the system for normal operation.

Mar 24, 2015 | 2004 Mercury Sable

1 Answer

Diagram Power Window


What year,make and model is this and also how do you know the window motors are good?

Jun 09, 2013 | Cars & Trucks

1 Answer

2000 Jetta nothing works in the driver door


look for a broken wire inside the boot between the door and body

May 08, 2012 | Volkswagen Jetta Cars & Trucks

1 Answer

Problem with door lock and power mirror


The switches for the mirrors and window I believe are all run through the master window control switch. It doubles as a switch and module.

Jan 05, 2012 | 2004 Ford Explorer

2 Answers

Doorlocks dont work except from passenger side. mirrors dont work. windows dont work from anywhere


First, check all fuses to make sure that none are blown.

If the door lock switch works on the passenger side, then the drivers side door lock switch is probably faulty. Use a multi-meter to test the Drivers Side Door Lock Switch (Black and Pink/Light Green wires unlock the vehicle, and the Black and Pink/Yellow wires lock the vehicle)
If the switch is tested and found to be operating properly, you may have a faulty Body Security Module or Drivers Side Door Lock Actuator.

If neither of your Power Mirrors are working, you probably have a faulty Exterior Rear View Mirror Switch, Power Mirror Module, or blown Central Junction Box Fuse.

If none of your Power Windows are working, you probably have a faulty Accessory Delay Relay or a blown fuse in your Central Junction Box or a faulty Master Window Adjust Switch (all of the Power Window Switches feed through this Master Window Switch). If the Power Windows didn't stop working at the same time, you may have faulty Window Adjust Switches, or faulty Power Window Motors, this is very unlikely though. It would also be a good idea to inspect the wiring for any obvious damage.

Mar 15, 2011 | 2005 Ford F-150

1 Answer

Passenger door electric locks, window and mirror wont work, also keyless entey is inop


{: ) If the PDM fuse at the IP fuseblock is found okay, try to reprogram the passenger door/window switch, before proceeding on more diagnostic checks and possible replace.

Feb 27, 2011 | 2003 GMC Yukon XL

1 Answer

Windows will not work from drivers side master switch or the single door switches lock not working also remote mirrors dont 2001 jeep grand cherokee ltd


First thing to check is the fuses. Look underneath the drivers side steering wheel (to the left) for a covered fuse box. Remove the cover and find the fuse that controls the locks and windows and mirrors (two-three separate fuses) Pull them out "one by one" and see if they are burned out. If they are, replace them with the correct number fuse.If it is not the fuse, the door lock actuator has failed (for the door locks) or the master switch that controls the locks is bad. Go to your local junk yard and find a replacement for cheap

http://forums.automotive.com/70/16389/general-auto-repair/2001-jeep-grand-cherokee-power-windows-defect/index.html

Feb 17, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Power windows inop


a brake in ur wires in the door,on a 04 grand i had the same problem,in the wire harness were the junction box is rust had broken one of the male prongs

May 04, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

1 Answer

Power Locks


there is an update for the bcm on 2005 caravans for this problem...you need to see your local dealer

Sep 06, 2008 | 2006 Chrysler Town & Country

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...