Question about 1997 Mitsubishi Montero

1 Answer

Need to know how to install the AC belt. it popped.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 139 Answers

There should be a belt tensioner inline of the belt somewhere use a ratchet or wrench to pull on it and belt will get slack in it change the belt but first I would take off old belt and make sure the ac compressor isnt froze up if it is it will only pop the new belt.

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my belt on my 1993 new yorker pop off in the rain?


Could be a couple things. All pulleys should be in line with the belt. Any pulley, like the power steering pump, or AC compressor, alternator, etc...could be slightly out of alignment causing the belt to rub and when wet it is slippery enough to pop off. Another item could be the tensioning roller "or ideler roller" is not adjusted to be tight enough to take slop out of the belt. This would make the belt lose and could also jump a pulley....let me know if any of this helps??

Aug 05, 2011 | 1993 Chrysler New Yorker

3 Answers

I currently own a V6 3.0 L Mercury Sable LS. The AC pulley has stopped working entirely as the ac clutch has ground it into the compressor. I need to know the length of a serpintine belt with no ac. I...


Talk to your automotive supply. My understanding is that a Non-AC belt will run right thru the area where the AC pulley is. You can get a bypass pulley that will allow you to avoid the AC and it's pulley and a specific belt for that setup.

Mar 13, 2011 | Mercury Sable Cars & Trucks

1 Answer

So this is the first time I'm trying to do work on my car so I figured the belts are the best place to start, but one problem where are they located? I am trying to change the two belts known as my...


When you pop the hood the belts are to the leftside.you will need to remove the pass/side fender cover to see lower part of belts, heres a diagram to help you remove and install belts correctly, loosen bolts A-B to remove the ac/ alt belt loosen A a few turn and B is what releases tension as you turn it, after you tighten the belt then you will tighten A bolt, same with the other belt you loosen C-D bolts a few turns then loosen E to release the tension on the belt then install new belt and thighten bolt E after the belt is tight then tighten C-D bolts, hope this helps. good luck.dis regaurd the wiring diagram,1561ac9.gif0a0a47b.gif

Oct 09, 2010 | 2006 Nissan Murano

1 Answer

I jst need to know were does th blowmotor for ac is instal 02 kia


Hello, most blower motors a normally mounted under the the dash on the passanger side foot area. It usually covered by abs plastc sheald, simply pop that off or un screw it to remove it.

Mar 24, 2010 | 2002 Kia Spectra

3 Answers

Installation of new serpentine belt on 2002 Chevy Cavalier


Use a 3/8" socket end to rotate the tensioner counter clockwise. It may seem stiff, but that's a good thing... you want the tension to be there. After it's off the tensioner the belt will pretty much just come out of place and off the other pulleys. ***make sure you orientate the belt as it was originally (ac or w/ ac)...diagram should be on the front shroud.

Oct 08, 2009 | 2000 Chevrolet Cavalier

2 Answers

Ac bypass avalible


You can Bypass the Compressor By Purchasing a Smaller Belt and Install Leaving the Compressor out of the Install.

Jan 23, 2009 | 1995 Dodge Neon

1 Answer

'93 Mercury Sable Serpentine Belt installation without using AC


You need to have an automotive technitian install a new belt because there is a certain path the belt must follow before it will go on, plus the belt must go around the A/c as it is part of the path. You just don't have to use the A/C.

Tell the tech that the belt broke so that he can look for a reason as to why the belt broke.
Bill

Nov 19, 2008 | 1993 Mercury Sable

1 Answer

AC BELT NEEDS CHANGED


You have to remove the main serpentine belt first. this is done with a 15mm wrench put on the tensioner. then from the bottom you can get to the a/c belt tensioner. install a 3/8 ratchet on it and remove tension from belt. I find the only way to get belt on and off is too slip it off the tensioner then off the backside of crank pulley then slide off of a/c compressor then install new belt onto the crank letting it fall off the backside run belt around compressor tensioner then work around crank pulley

Nov 17, 2008 | 2003 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...