Question about 2008 Dodge Ram 2500

1 Answer

My truck wont go in 1st,2nd or reverse when truck is running it will go inthe rest of the gears,but if i shut the truck off u can put it in any gear and start it up and go

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 148 Answers

It sounds like the clutch is getting worn or the slave cylinder is not pushing the pressure plate in far enough.If at all possiable try bleading the cluthch slave cylinder an see if that helps.

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Audi A3 2.0 fsi sline Quattro is struggling to find gears ( very stiff to change and impossible to find reverse with the engine running)


First check the fluid level and make sure it is correct. If it's good you will then need to go to the dealership to have the codes pulled. I hope the problem is the fluid because it will be expensive otherwise.

Jan 04, 2015 | 2005 Audi A3 2.0

1 Answer

2000 a4 w0nt select 1st gear or 2nd or reverse with engine runnin bu


SMELLS LIKE SOMETHING NEEDS TO BE CHANGED AND THAT IS PROBABLY THE CLUNCH!!

Feb 23, 2014 | Audi A4 Cars & Trucks

1 Answer

I have a 91' ford f-150 that I pulled out of a parking lot and shifted from 1st to 2nd and instead of going into second it became stuck in fourth. then I proceeded to pulling the three screws out from...


if there has been no abuse or no chance somethind bent shifting rods under veh. check for loose or worn out shift rod connections,If internal trans shift drum problems your world just got more complacated

Aug 26, 2013 | Cars & Trucks

1 Answer

1995 Ford Bronco engine dies when shifted into drive but runs in reverse or 1st gear


Could be fuel filter,air filter,tune up,wires,coils.low idle too low.

Jun 13, 2013 | 1995 Ford Bronco

1 Answer

CAR IS IN GEAR AND WONT MOVE...WHERE IS THE TRANSMISSION DIPSTICK?


Should be on the driver's side near the transaxle.

Jul 18, 2012 | 2001 Oldsmobile Alero

1 Answer

5th gear went out yesterday when u put it in 5th its 3rd gear. Then today reverse 1st and 2nd went out. Reverse 1st and 5th is 3rd and 2nd and 4th both is 4th gear


time to put a new tranny in that jet most of the time it costs to much to repair it then replace it i have done may tranny rebuilds and replacements to me i would just tell you to replace it at least you will get a better warrentee and stuff

Feb 27, 2011 | 1988 Volkswagen Jetta

1 Answer

Only runs in 1st and 2nd gear and reverse.


This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Dec 14, 2009 | 2006 Hummer H3

1 Answer

My 92 honda accord will not go into 1st 3rd or 5th gear


check shift fork adjustment. make sure you bleed the slave cylinder.also check shift cable adjustment.

Apr 11, 2009 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...