Question about 2000 Dodge Durango

1 Answer

What size hex nut is on the brake caliper - 2000 Dodge Durango

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

IF you are talking about the allen screws on the front, they are 7mm provided that no one has replaced them before. It should be a 13mm it is externally.

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 ford expedition front brake caliper jex size


is that hex size
just buy a hex drive set
wont be the last time you need hex set

Apr 12, 2017 | Ford Cars & Trucks

2 Answers

What size allen needed to remove break pads


Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

1 Answer

What size allen wrench for brake calipers on 2001 Dodge Dakota 2WD 3.9L and what size is the nut holding the rotor on? Standard or Metric?


a 7 mm hex head wrench for the caliper bolts. the nut that holds the bearings in place is usually a 1 inch or 1 1/16 inch, but a pair of pliers should be enough to take the nut off after the cotter pin is removed. when you put the nut back on DO NOT over tighten it or you will damage the wheel bearings.

Aug 07, 2011 | 2001 Dodge Dakota

1 Answer

What is the socket size of the nut holding the front rotor on a 2005 toyota corolla? its not a hex nut but a 12 point socket?


the only things that are holding the rotor on is 1) the brake caliper which i believe has 2 14mm screws and 2) the brake caliper bracket which has 2 17mm screws holding it in place.once you remove these 2 parts,tap on the rotor( where the wheel goes bolted on )with a hammer and it should come off easily.if not spray some penetrant on the studs that hold the tire on, then tap on it some more and it should come off.hope this info helps.take care and good luck, manny

Apr 03, 2010 | 2005 Toyota Corolla

1 Answer

I need to know the size of the bolts that hold on the brake caliper housing and the bolts that hold on the brake caliper


I believe the brake caliper bolts at the slides are 13MM hex and the bracket bolts are either 18MM or 21MM

Nov 07, 2009 | 2002 Chevrolet Avalanche

2 Answers

How to change rear brake disk on 01Chevy Silverado


need a torx 55. must remove caliper in the bracket then remove the caliper. Bracket bolts are 17mm I think.

Oct 23, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Tool to remove front brake caliper to replace rotor Escape 2005


You need a 7mm socket, which are available at auto parts stores.

Jun 20, 2009 | 2005 Ford Escape

1 Answer

Front brake rotors.


1. Loosen the wheel nuts slightly. 2. Raise the front of the car and support it with safety stands in the proper locations. 3. Remove the wheel nuts and front wheel. 4. Remove the brake hose mounting bolts. 5. Remove the caliper bracket mounting bolts, and hang the caliper to one side. CAUTION: To prevent accidental damage to the caliper or brake hose, use a short piece of wire to hang the caliper from the undercarriage. 6. On ABS equipped vehicles, remove the wheel sensor wire bracket, then remove the wheel sensor from the knuckle but do not disconnect the wheel sensor connector. NOTE: Use ball joint removers to separate the ball joints from the suspension or tie-rod end. 7. Clean any dirt or grease off the ball joint. Remove the cotter pin from the tie-rod end ball joint castle nut and remove the nut. 8. Apply grease to the special tool on the areas shown. This will ease installation of the tool and prevent damage to the pressure bolt threads. 9. Install a 10mm hex nut on the ball joint. Be sure that the hex nut is flush with the ball joint pin end to prevent damage to the threaded end of the ball joint. 10. Adjust the jaw spacing by turning the pressure bolt. NOTE: If necessary, apply penetrating type lubricant to loosen the ball joint. 11. Once the tool is in place, turn the adjusting bolt as necessary to make the jaws parallel. Then hand tighten the pressure bolt, and recheck the jaws to make sure they are still parallel as pictured above. 12. With a wrench, tighten the pressure bolt until the ball joint shaft pops loose from the steering arm. WARNING: WEAR EYE PROTECTION. THE BALL JOINT CAN BREAK LOOSE SUDDENLY AND SCATTER DIRT OR OTHER DEBRIS IN YOUR EYES. 13. Remove the tool, then remove the nut from the end of the ball joint and pull the ball joint out of the steering/suspension arm. Inspect the ball joint boot and replace if damaged. 14. Remove the cotter pin from the lower arm ball joint castle nut, and remove the nut. 15. Install a 12mm hex nut on the ball joint. Be sure that the hex nut is flush with the ball joint pin end, or the threaded section of the ball joint pin might be damaged by the ball joint remover. 16. Use the ball joint remover, 32mm, as shown to separate the lower ball joint and lower arm. NOTE: If necessary, apply penetrating type lubricant to loosen the ball joint. 17. Remove the knuckle protector. 18. Remove the cotter pin from the upper ball joint castle nut, and remove the nut. 19. Install a 10mm hex nut on the ball joint. Be sure that the hex nut is flush with the ball joint pin end, or the threaded section of the ball joint pin might be damaged by the ball joint remover. 20. Use the ball joint remover as shown to separate the upper ball joint and knuckle. NOTE: If necessary, apply penetrating type lubricant to loosen the ball joint. 21. Pull the knuckle outward and remove the driveshaft outboard joint from the knuckle by tapping the driveshaft end using a plastic hammer, then remove the knuckle. 22. Remove the knuckle from the hub unit. 23. Remove the four flange bolts, then separate the hub unit from the brake disc.

Jun 08, 2009 | 1994 Honda Accord

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...