Question about 1996 Jeep Grand Cherokee

1 Answer

How do you replace front hub assembly on jeep grand cherokee 1996

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Remove brake assembly and rotor, including axle nut (do first...about 175 ft lbs torque...a real bear to get loose) There are three 12point bolts on backside of steering knuckle. loosen them and back out about 1/2 inch...Give them a good shot with a hammer to begin pushing bearing from knuckle. (I leave an old wrench on each as I hammer so they don't deform too much.) Use lots of wd40 and sometimes you need to get a chisel and hammer between the bearing and knuckle to separate them. Reverse process (except for hammering part) to replace.

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 jeep grand Cherokee 4x4 the right front tire keeps locking up I don't know what is wrong


Have you changed the hub assembly or had the front differential checked out?

Nov 01, 2014 | 1998 Jeep Grand Cherokee

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

2 Answers

How do I remove and install hubs on the front end of a 97 jeep grand cherokee?


It is actually very easy. Lift the vehicle and support it properly remove the 5 lug nuts retaining the wheel. Remove the wheel. If it is a 4 wheel drive remove the spindle nut locking the c.v. axle to the hub. Remove the washer. Push the axle through the splined hub. using a 13 mm or 15mm depending on the hub remove the three bolts reatining the hub assemble to the steering knuckle. assemble in reverse order.

Feb 27, 2011 | 1997 Jeep Grand Cherokee

1 Answer

After driving the jeep for 20-30 min the front


it sounds to me like you need tie rods and hub assembly's and bushings

Mar 14, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Noise in rear of 04' Jeep Grand Cherokee


have the axel bearings checked and if there is enough fluid in the rear.

Sep 13, 2009 | 2004 Jeep Grand Cherokee

1 Answer

CHaging signal light in a 96 Jeep Grand Cherokee


Review this info: ZJ-Secc-8L-Lamps (page Lamps 8L-5 and next)

Good luck, and rated me!!!


Aug 02, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Need instruction on how to replace CV joints on 1997 Jeep Grand Cherokee


remove front wheels , one or both at a time , remove caliper and rotor , remove cotter pin and nut on shaft , there are three or four bolts on back side of hub , remove the hub bearing and shaft should slide out , i would see if complete rebuilt assemblies are available , faster and easy this way

Feb 19, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...