Question about 1996 Eagle Vision

Open Question

How to reset the alarm syatem .. horn flashing

How to reset the alarm syatem ..went to open door horn flashing lights wont quit . had to take battery cable off .. when putting back ,same problem..

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The alarm wouldnt quit going off i got it to quit and now the car wont start but the battery is charged d o reset it somehow or is there a code to fix it ?


try locking and unlocking your doors , look at the alarm light see if it is flashing or if it is on with out flashing , if its flashing it means the alarm is off if it is soled it is set , if this doesn't work then disconnect the battery for 1 minutes or more

Jun 22, 2014 | 1996 Cadillac DeVille

Tip

How to set & cancel theft deterrent system or how to set & cancel security...


Theft deterrent system (on some models)

Theft deterrent system is designed to deter vehicle theft. The system flashes the turn signal lights and turns on the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn when it detects abnormalities such as follows:

• Any door or hood is forcibly opened.
• The batter terminal is disconnected and then reconnected
• The system control is disconnected and then reconnected.
• Abnormal impact is detected when the impact sensor function is on.

The system flashes the turn signal lights and turns the interior light or the signal lights only (depending on the model), and sounds security horn and vehicle horn if someone attempts to damage or break into your car.

Setting the system

You can set the system with or without the impact sensor function. For details, see "Canceling the impact sensor" below.

1. Turn the ignition key to "LOCK" and remove it.
2. Have all passengers get out of the vehicle
3. Push the lock (set) switch on the wireless remote control key once. At this time, the turn signal lights flashes once and the security indicator light comes on.

The system is set after 30 seconds. At this time, the security indicator light start flashing slowly.

Once the system is set, you cannot start the engine until you cancel the system.

The system will not be set in the following cases.

• When any of the door is open; security horn sounds for 1 second, close the door and set the system again.
• When the hood is open; close the hood securely.

Canceling the Impact Sensor

The impact sensor can be cancelled to prevent false alarms from being triggered incase of the following conditions:

• When parked in the noisy area
• The vehicle body or glass is subjected to a strong impact from the (such as in highly pressurized car wash).
• When transporting by a car carrier or ferry.

To cancel the impact sensor;

1. Lock the door by pushing the lock (set) switch on the wireless remote control key once, and turn signal light flash once
2. Then push the lock (set) switch twice within 5 seconds. At this time, the turn signal flash 5 times to indicate the impact sensor function is disable.

The impact sensor is deactivated as long as the system remained armed.

Canceling the system

The system will be cancelled by the following two ways:

• Turn the ignition key from "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch

If the turn signal lights flash 3 times, the system has been alarmed. Check to see if there is any abnormality with your vehicle.

If any of the doors is not opened within 30 seconds, all doors will be automatically locked and the system will be set.

When the system is set

Activating the system; When the system detects abnormalities such as follows, it flashes the turn signal lights and turns on the interior light or the turn lights only (depending on the model) and sounds the security horn and vehicle horn of 30 seconds.

• Unlocking any door without using wireless control
• Any door or hood is forcibly opened.
• The battery terminal is disconnected and then reconnected.
• The system control assembly is disconnected and then reconnected
• Abnormal impact is detected when the impact sensor function is on.

Reactivating the alarm;

Once set, the system automatically resets the alarm after the alarm stops.

The alarm will activate again under the same circumstances described in "Activating the system".

Stopping the Alarm

The alarm will be stopped by the following two ways;

• Turn the ignition key from the "LOCK" to "ON" position.
• Unlock any of the doors by pushing the unlock (cancel) switch.

The system can be cancelled by these ways at the same time.

If the battery becomes discharged due to the vehicle being unused, for a long time etc., when the battery is recharged or replaced, the system will activate the alarm. If this happens, immediately unlock any of the doors by pushing the unlock (cancel) switch, and the alarm will stop.

Testing the system

1. Set the system
2. Insert a wireless remote control key into the key hole on the driver's door handle, and unlock the door.
3. Open the door, and an alarm will sound.
4. Stop the alarm by pushing the unlock (cancel) switch.
5. Repeat this operation for the front passenger's door.

Good luck.

on Nov 08, 2010 | Toyota Pickup Cars & Trucks

1 Answer

2009 honda civic lights flashing horn blowing security alarm


try disconnecting the battery neg lead and the pos lead then join them together for 5 mins then reconnect the battery and see what happens ,it might just reset the fault for you .

Apr 27, 2012 | 2009 Honda Civic 1.4

1 Answer

My s class 2004 mercedes wont lock. I try to lock it from the inside, it doesn't work. I press the remote, the light flashes, but it doesn't lock. When I drive; the doors doesn't lock like usual. The...


hi, if any doors, boot or bonnet is open it will not lock. there are SWITCHES that has to be set.for the system to recognize it is closed. please check all openings even windows. ONLY DO THIS IF.if the BATTERY HAS BEEN TAKEN OFF OR BATTERY HAS BEEN DISCONNECTED. the SYSTEM MAY NEED RESETTING. the battery NEGATIVE lead needs to be taken OFF and place the NEGATIVE LEAD ON THE TERMINAL (A NOISE WILL BE HEARD), the ALARM and CENTRAL LOCKING SHOULD BE RESET, if the ALARM DO'NT SOUND put the lead ON and OFF a FEW TIMES. CLAMP THE BATTERY LEAD CONNECTION TIGHT and press the ALARM BUTTON OFF and retry locking SYSTEM. this will work if everything is O. K. gerry

Sep 13, 2010 | 2004 Mercedes-Benz Mercedes Benz S Class

2 Answers

Just replaced battery on 2005 tundra, how do I reset the vehicle alarm. The alarm now sounds whenever I open the doors.


Anytime the alarm sounds when opening the door with the key, get into the truck anyway, place the key into the ignition key switch and turn it on and off 2 times. The horn will stop blowing and the lights will stop flashing. You're ready to go.......

Nov 05, 2009 | 2004 Toyota Tundra

1 Answer

How can I reset my Factory Alarm on my Jeep it wont run


Alarm Module Reset Procedure
NOTE: This information applies to a Vehicle Theft Security System (VTSS) that was armed when the battery was disconnected and reconnected.
When the armed VTSS senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed following a battery reconnection.
The power-up mode will also apply if the battery goes dead while the system is armed and battery jump-starting is attempted. The engine no-run feature will prevent the engine from starting until the alarm system has been actively or passively disarmed.
Passive disarming of the Vehicle Theft Security System (VTSS) occurs when the vehicle is unlocked using the key to unlock either front door or the lift gate. Active disarming of the VTSS occurs when the vehicle is unlocked by depressing the Unlock button of the Remote Keyless Entry (RKE) transmitter.
Once the alarm has been activated (horn sounding, lights flashing, and the engine no-run feature), either disarming method will deactivate the alarm.
Depressing the Panic button (if equipped) on the RKE transmitter will also disarm the VTSS, but the horn will sound and the lights will flash for about three minutes as part of the Panic feature. The horn and lights can be stopped by pressing any of the RKE transmitter's buttons or driving the vehicle above 15 mph.

Jan 28, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Back door wont open after can went dead and had to get a boost


try checking the fuses for the swithes themselves, usually under the dash or beside the doors

Dec 14, 2008 | 2004 Chevrolet TrailBlazer

2 Answers

Help! my car is possessed


i may be wrong at this but i think it's your alarm system. headlights, doors and horn all connects to an alarm system (if your alarm system does this) i mean, some alarms, when you unlock or lock your car, the lights turn and horn blows simultaneously with the alarm. if you have an alarm system that seem to malfunction, it may also affect your doors, horn lights etc. have it checked or replaced.

well, as ive said, i may be wrong. =)

Jul 15, 2008 | 1997 Honda Civic

Not finding what you are looking for?
1996 Eagle Vision Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Stewart Dibbs

Level 2 Expert

267 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...