Question about 1988 Toyota Corolla 4 Door

1 Answer

How do i replace wheel stud on 88 corolla? front driver side

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

You will have to take the disc and caliper off too.
Then put the wheel nut back on, screw the nut until the top is level with the thread on the stud. A few good hits should do it, when you put the new one in put a few washers on the stud, then put the nut on and tighten up just so the stud is in right.
Here is a diagram will show you the stud.
i hope this helps!


how do i replace wheel stud on 88 corolla? front - 6611148.gif

Posted on Jul 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front wheel studs on 2011 Kia Forte


If you can find just the studs and not have to buy the whole hub assembly, screw a lug nut on flush to the stud and drive it out with a hammer, make sure its in a position to have room on the back side. Put in new stud and with a few spacers tighten a lug nut to seat it.

Aug 15, 2014 | Cars & Trucks

1 Answer

How replace rear wheel stud on '90 corolla drum brakes


Remove the drum,turn where it has nothing blocking to come out.Don't hit stud directly with hammer,you will cause the end to get bigger and it will damaged the hole,if you have punch that is small in diameter than stud,use that with hammer,turn drum again so next stud it is free to come out.

Jul 29, 2017 | Cars & Trucks

1 Answer

Broken wheel stud


Unless you hit a curb or something you have bumper to bumper warranty for 3yrs.36 k miles.If not then you can remove the wheel and brake caliper and rotor.Then pound the stud out with a hammer and reinstall the new one.Use a socket or some type of spacer and put on new stud once you have put the stud through the axle.Install the new nut on and start tightening til the stud is seated on the axle.Reinstall the wheel and torque to specs.Depending on type of wheel could be 80-100 ft.lbs.Hope this helps.Good luck.

Dec 23, 2009 | 2002 Pontiac Grand Am

1 Answer

I need to replace the studs on the front drivers side rotor, three of the broke off when I was removing the wheel to replace the brakes. What does it require?


The studs are in the hub behind the rotor and it has to be removed because the studs have to be driven out with a hammer (and punch when broken) and driven back in. When you buy the new studs, you'll see what I mean.

Oct 26, 2009 | 1998 Nissan Altima

1 Answer

Sheared off Wheel Stud


Not realy that critical sense theres 4 others, but it should be replaced as soon as posible. They put 5 on there for a reason.

Oct 06, 2009 | 1999 Pontiac Grand Am GT

1 Answer

I have a 2001 toyota corolla and I am wondering if a wheel from a voltswagon golf with 4 wheel studs would fit my toyota corolla with 4 wheel studs? Pleas if you can give me an detailed answer thank you


The VW wheels measure 14x6 57.1 and your corolla wheels are 14x5.5 54.1, the vw wheels are 1/2" wider but as long as you use the proper size tires for your corolla you wont run into any problems. also the bolt patterns will match they are both 4x100.

Oct 24, 2009 | Toyota Corolla Cars & Trucks

1 Answer

Broke stud on front left side


Yes you can replace the broken wheel stud. The wheel studs are pressed into place, and a vise will work to press it out, and in. You will have to remove the wheel hub, and then use a deep well socket and a bolt or something smaller than the actual stud to remove it with a vise. To replace it, you will need to use the deep well socket on the thread side of the stud, and press the new one in with the vise.

I hope this helps you, and I wish you luck with your repair.

Apr 25, 2009 | 2003 Pontiac Sunfire

1 Answer

Snapped wheel studs on front wheels and need to change them


you have to hammer the studs through the spindle to get them out. then **** the new ones in with a nut and lots of washers. put grease on the washers and threads before you **** the studs in.

Apr 15, 2009 | 1988 Toyota Corolla 4 Door

1 Answer

1990 Sentra How it remove and replace lug studs on front wheel


there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Feb 27, 2009 | 1990 Nissan Sentra

1 Answer

Two Broken Wheel Studs on Front Driver's Side


It would be best to have the work carried out at a garage of your choice. A garage you have used before and trust to do a good job. Depending how long it takes to free the studs, will depend on the final price.

Nov 24, 2008 | 2000 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

485 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...