Question about 1999 Saab 9-5

1 Answer

I have a 95 est areo on a 53 plate how do i ajust the hand brake plaese

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Lift the armrest, inside the compartment remove the rubber liner. Through the hole you will see a threaded rod with a nut. Using a deep 10mm socket thighten the nut. That's the easy way. The hard way is removing both rear wheels and adjusting the hand break drums pads located inside the hubs with a screwdriver.

Posted on Aug 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Holden commodore problemsi have a vy commodore brakes just re-knewed but carnt see where to adjust hand break cable mcan u help


most times the hand brake top screws down to adjust the brake but there is normally an adjustment under car where the cables from the rear wheels join the single cable going to the hand brake If the hand brake top has been screwed down all the way loosen it up al the way before adjusting anything

Aug 20, 2014 | Cars & Trucks

1 Answer

HAND BRAKE AJUSTMENT for Kia Picanto can notadjust the hand brake and how do I get at the hand brake tensioner


Brakes are self adjusting whether disc or drum.
I'm guessing the fault is lack of servicing of the brakes. You shouldn't have to alter the cable adjustment to offset a brake system in poor repair. Get the brakes cleaned and correctly set and you should find the handbrake sets itself. Check the cables release properly and move freely to allow self setting to occur.

Nov 05, 2013 | Cars & Trucks

1 Answer

How do I tighten the hand brake cable on my 94 Toyota Tercel?


First make sure the rear breaks are ajusted or replaced when worn out drum to be skeemed aswell. Usally whe rear brakes are ajusted hand break will stop car on two to four clicks on hand brake rachet. If brakes is ajusted check cables for wear . Then ajust cable insite car remove hand brake cover and you will see a ajustable screw or nut. Rememeber to put the handbrake on four clicks and dont tighten screw or nut to much the brakes will lock

Feb 12, 2013 | Cars & Trucks

1 Answer

How do i ajust the hand brake for a daewoo kaloss 2003


There is a nut under the hand brake boot tighten it clockwise until the hand brake lever just starts to engage the rear brakes after 3-4 clicks of the ratchet.

Nov 05, 2012 | 2005 Daewoo Kalos 1.2

2 Answers

How do i adjustment the handbrake on a rover 75 on a rover 75


should be self ajusting if not there should be a nut conected to the hand breake either remove cowling around hand brake if not i may be underneath the car where hand brake comes out of the floor but most cars now can be ajusted by removing the hand breke trim

Sep 19, 2012 | 1999 Toyota Corolla

1 Answer

Kia caren 53 model handbrake ajustment


2 10 mm wrench's and a screwdriver are needed. lift the rubber boot and adust the cables with the wrenchs by loosening the locknut first then take the slack out of the cables evenly while not letting them turn by holding them with the screwdriver . when you can set the brake on the third or fourth notch or click then its perfect,

Jul 22, 2012 | Kia Carens Cars & Trucks

1 Answer

The rear brakes in my 95 vauxhall cavalier locking


it sounds like they are not ajusted right

May 05, 2010 | 1995 Chevrolet Cavalier

2 Answers

Rear discs and handbrake on 2002 S80 D5


tighten the hand brake tensioner

Jun 27, 2009 | 2002 Volvo S80

1 Answer

Replace rear brakes adjust handbrake


The hand brake hardly ever needs ajusting. See your hand brake mechanincly spreads your rear brake shose inside the drum. Therefore just replace your rear shoes and make sure there ajusted right and you should have no more problems with that part of your car. PS make sure you put some 3M paste on the contact points on your backing plate to avoid a squeak in the near future.

May 16, 2009 | 2001 Ford Focus

1 Answer

Can not remove rear brake drum on a 2000 Buick Century


Yes you do, but chanses are the ajusters are froze up. The best thing to do isto get a pry bar between the backing plate and drumb and pry and hit the other side with a hammer, or maybe if you can pry it out far enought to pop the ajuster out, or cut the heads off the pins on the back side of backing plate that hold the shoes to backing plate.

Apr 04, 2009 | 2000 Buick Century

Not finding what you are looking for?
1999 Saab 9-5 Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...