Question about 1998 Toyota Camry

1 Answer

Replace Camry 2007 front bumper cover

HOW ?

Posted by on

  • jared voulo Jul 28, 2009

    is this done on both driver and passenger side ?

    Thanks



  • jared voulo Jul 28, 2009

    Fast answer !!! Thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 601 Answers

Hi...
Remove 8 clips and 8 screws from the under body of front bumper.
I attached diagram because the real picture does not make sense sometimes.
Diagram below only shows half of them(4clips & 4screws). so do the same thing on the other side
That will bring down the bumper with the fog lamp.
Replace Camry 2007 front bumper cover - b06b543.jpg Thanks
Smith

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace right front fender on a2007 replace fender 2007 chevy impala


There are four bolts and the hood hinge to remove on top. Remove the tire, remove the inner fender cover( seven or eight screws). There are two bolts to remove the fender from the front bumper cover. And one bolt to remove from inside the door( open the door, remove the cloth, the bolt is close to the top). Replace in reverse.

Oct 09, 2014 | 2007 Chevrolet Impala

Tip

How To Remove Front Bumper Cover Audi A4 2005 2006 2007


Learn how to remove the front bumper cover on a Audi A4 2005 2006 2007

on Jan 27, 2016 | Audi Cars & Trucks

Tip

How To Replace Install Front Bumper Signal Light 1995-96 Toyota camry 1AAuto.com


How To Replace Install Front Bumper Signal Light 1995-96 Toyota camry 1AAuto.com

on Apr 26, 2012 | 1995 Toyota Camry

1 Answer

I lost my lower front bumper (the black plastic part) i have a new one but not sure how to put it on


There is a simple procedure to do that.And basic tools are required.

Click the link below for detailed procedure:----
How to Replace Front Bumper? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-front-bumper-on-audi-a4.html

-----------
How to Replace a Front Bumper Cover? http://technoanswers.blogspot.com/2011/07/how-to-replace-front-bumper-cover.html

----------
How to Attach the front bumper cover to the fender? http://technoanswers.blogspot.com/2012/01/how-to-attach-front-bumper-cover-to.html

--------------

How to replace Bumpers?
http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-bumpers-on-acura-car.html

--------------
This details will help.
Thanks.

Oct 09, 2012 | Cars & Trucks

1 Answer

How to remove 2007 toyota sienna front bumper


I have written a step-by-step tutorial on how to remove (and replace) the bumper of a 2004-2007 Toyota Sienna on my blog: John Fixes Stuff How to Remove the Front Bumper on 2004 2007 Toyota Sienna

Feb 01, 2012 | 2007 Toyota Sienna

1 Answer

Remove front bumper


For front bumper removal,i suggest you to click the link below :---How to Replace Front Bumper? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-front-bumper-on-audi-a4.html
-------How to Attach the front bumper cover to the fender? http://technoanswers.blogspot.com/2012/01/how-to-attach-front-bumper-cover-to.html

-----------------

This will help.

Thanks.

Dec 14, 2011 | 2007 Suzuki SX4

1 Answer

How do you replace a bumper bar ....do you need a whole new skirt


Bumper bar? Skirt?
There is a bumper reinforment behind the bumper cover.
Front or rear???
Either way there are some plastic retainers on top. You may need to remove a grill which would have some sort of retainer. The retainers usually have a center section that prys up some and the retainer will then pull out.
There should also be some retainers on the undersides of the bumper covers.
There is just about always a bolt going up through the bumper cover into the rear quater panel or front fender right in the wheel well edge. Sometimes there is a guide that the cover slide onto as well. You may need to remove the tail lights. There will be nuts on the inside behind the trim panels or the headlights. they usually have some clearly seen bolts holding them in (about 4 give or take)
Unplug any lights and they can usually be left in the bumper cover.
Then off comes the cover.
From there you may find a styrofoam pad. Don't lose that as it helps the cover keep its shape in the heat. And either the reinforment will be bolted or welded to the frame rails.

Sep 06, 2011 | 2007 Toyota Camry

1 Answer

How do I replace a tail light assembly on a 2007 toyota camry?


I tried to search all over the places on internet but to no avail. So did it on my own and the result was successful.

I replaced the passenger side rear tail light assembly of my Toyota Camry 2007. The method is same for the late models till 2011 no matter what the side is.

Its very easy to unscrew 3 nuts inside the trunk after removing the only portion of cover that covers the light but this is not it, there is a bracket under the light assembly which actually holds the edge of bumper and in order to pull it out of the bumper, bumper has to be partially taken out or loosen out.
To began the process I took the wheel out to unscrew 2 screws located right behind the wheel on the lining of bumper cover holding the mud flapper at the same time, if you have small philips screw driver of approx 2" length you might not need to remove the entire wheel. please see the image 1 as I took the pictures while fixing the light up and that too all alone.

10_14_2011_1_06_33_am.jpg
There are 2 more screws to be taken out one holds the flap and other holds the bumper cover, all need to be taken out to bring the flap apart.

10_14_2011_1_19_48_am.jpg
Now there is a most critical and important part for the entire job, after loosing the screws and after pulling the flap down there is a hidden bolt which will come with small sized socket (usually available in basic socket set kit)


10_14_2011_1_25_17_am.jpg

Loose the bolt like this.
10_14_2011_1_27_20_am.jpg

Now just hold the loose side of the bumper cover and pull it out towards yourself, that particular cover side will easily come off.

You need to loose another screw hiding in the cover right behind the bumper, open the cover with a help of the plain flat screw driver and take the bolt out.




10_14_2011_1_33_32_am.jpg

You have just loosen the edge of bumper cover holding the bracket of light, just pull the light towards you while facing it (do not forget to unplug the power supply sockets as in next image) bend it little to the top and slide the bracket out of the bumper cover edge and you got the light assembly out in your hand.







10_14_2011_1_51_50_am.jpg

Disconnect or unplug the power supply from the sockets, just press the plastic tip and pull the plug out from the light socket, if you just forget the order don't worry, the gray will go in gray and black one in black (please do this in the very first stage as i forgot to put this in a beginning)


10_14_2011_1_52_18_am.jpg

Now hold the new assembly, slide it's bracket in the bumper cover edge (the way it was taken off) slide the light carefully as there is a round shape plastic part in the body needs to hold the corner edge of the light assembly


10_14_2011_1_56_35_am.jpg

Put the 3 nuts back on the light bolts from inside the trunk.




10_14_2011_2_00_13_am.jpg


Attach the power sockets.

Push the snapped out side edge of the bumper cover back to its framing, the click sounds will confirm its proper attachment now put all the screws back in a same way they were taken out but don't forget to putting back the mud flap.


10_14_2011_2_05_52_am.jpg10_14_2011_2_06_20_am.jpg


10_14_2011_2_09_05_am.jpg

At the final stage, just mount back moldings from inside the trunk, please refer to the images, there are 2 bolts and rest clip in typed sockets, sometimes while snapping the moldings out the white male female clips remain in their housings, just take them out with hand or screw driver and put them back carefully back to the plastic molding before tucking them back


10_14_2011_2_15_52_am.jpg


10_14_2011_2_17_16_am.jpg




10_14_2011_2_20_04_am.jpg10_14_2011_2_20_24_am.jpg


10_14_2011_2_24_16_am.jpg

Hope this will help you guys out !

This entire process was done without any help of trained or professional, please handle the task by keeping maximum safety precautions and at your own risk :)

Faiz.

Sep 10, 2010 | 2007 Toyota Camry

1 Answer

Replacing the skid plate on 07 Tahoe Z71


Remove bumper or use a swivel adapter to remove

Apr 29, 2009 | 2007 Chevrolet Tahoe

1 Answer

Need to replace the front bumper cover on a 1995 ford escort


its just the bumper cover.. once you buy the bumper cover it will replace your broke one,, however you my need to buy a bumpercover support..i think its only about $30 more..good luck keith...

Mar 15, 2009 | 1995 Ford Escort

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...