Question about 2002 Mercury Cougar

1 Answer

A screw is broken on trasmission mont how do i get it out

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 305 Answers

Drill a small hole in screw , buy a left hand thread screw from a hardware shop, when you screw in the left had threaded screw it will tighten up to a point where it will start to turn the exsisting broken screw out....
hope this helps....it really does work
please leave good feedback on fixya if you get the screw out, cos i do this for free in my spare time

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My inner door latch is broken in my 96 chey monte carlo i have the part but idk how to install it.


Remove the door panel, that is the part you have next to left arm when setting in seat. Look for screws holding it on. do you have a door panel tool ? If no you need one, pick it up at a parts store also the CHILTON repair manual for your year make and model, they are great at helping you not to break the door panel and do it correctly. I hope this is a big help, lee.

Feb 09, 2014 | 1996 Chevrolet Monte Carlo

1 Answer

The trasmission is stuck in park. is there a safety switch?


86394771
  1. Remove access hole cover by unfastening screw.
  2. Turn ignition key to "ACC" position and move shift lock solenoid rod (or manual release plate) toward rear side of vehicle by using screw driver or the like.
  3. In this state, select lever can be moved to any range or position.

Mar 02, 2011 | 2000 Suzuki Grand Vitara

1 Answer

How do you get to the set screw to slide the rear view mirror off the button in a 1996 Monte Carlo?


SOME GM UNITS HAVE A SNAP LOCK TO HOLD THE RVW MIRROR ON. BECAREFUL IF YOU TRY TO REMOVE IT. THERE HAVE BEEN MANY WINDSHIELDS BROKEN FROM INEXPERIENCE

Aug 29, 2010 | 1995 Chevrolet Monte Carlo

1 Answer

Fan switch only works on #5


There is a series of resistance-wire coils inserted into the ductwork. The different fan-speed selections add one or more of these coils in series with the fan, and the air flowing through the ductwork keeps the coils of wire from getting too hot. Look for a connector apparently plugged onto a small plate screwed to the side of the ductwork (maybe 1½" × 3 ") often right under the glove compartment.

I think that one of those coils of wire that is used for every speed selection but 5 is broken. High speed just connects straight positive power to the fan with none of those coils of resistance wire included.

Jun 23, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

Front sway bar on a 2000 monte carlo


Be very carefull because there are lines and wires that can be broken if the engine is lowered too far. Disconect the battery. Set the parking brake and chock the rear tire.
Put the car on jack stands and take off one of the tires. Put the jack under the rear of the engine cradle. You have to loosen the steering column set screw at the steering rack and loosen the two front bolts that hold the engine cradle to the chassis. Take the two rear cradle bolts almost all the way off and lower the cradle until you can wiggle the sway bar out. The steering will disconnect.
Reverse the procedure to put everything back where it belongs. The steering shaft is a "D" shape so it only goes on the rack one way. Tighten the set screw and torque the engine cradle to the required specification. 133 ft. lb.
IMPORTANT -- Take the car to an alignment shop and have at least the front aligned. The front suspension is attached to the cradle and can be moved out of alignment.
Complete instructions are found in Haynes Manual p/n 24048, chapter 10.

Nov 06, 2009 | 2000 Chevrolet Monte Carlo

1 Answer

How do i fix a broken speedometer on a 1995 monte carlo LS


There spedometer has a cable that runs to tranny and screws on. Sometimes this can unscrew or the flat cable end inside can get bent or broke.

Sep 26, 2009 | 1995 Chevrolet Monte Carlo

2 Answers

Z28


trasmission oil need to be cold you have trasmission line that bring the oil to the radiator to get cool off that cooler is crack and that why the oil goes in the prestone good luck pierre

Oct 11, 2008 | 1995 Chevrolet Camaro

1 Answer

1999 ford contour


trasmission solenoid is inside the trasmission normally on the side of trasmission inside you have to remove the side of trasmission the solenoid itself 50 to 90 $ but labour that another ball game 2 to 5 hour labour plus oil hope it help fixya our post thanks pierre

Jul 18, 2008 | 1999 Ford Contour

Not finding what you are looking for?
2002 Mercury Cougar Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...