Question about 1997 GMC Jimmy

1 Answer

How to remove the ignition cylinder - 1997 GMC Jimmy

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

You need to remove the steering wheel and the turn signal switch.You will see a small bolt that you remove and it will allow you to slide out the key cylinder.

Posted on Jul 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Relay switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. .
Remove the steering column filler panel.
Remove the knee bolster bracket.
Remove the instrument panel (I/P) cluster trim panel.
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

Dec 05, 2013 | 2005 Chevrolet Impala

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

How to change the spark plugs on peugeot 406 v6 3l coupe is this straight forward like a 4 cylinder car


1. Spark plugs removal

1.1. Front cylinder bank spark plugs removal:
1.1.1. Disconnect the battery from car terminals.
1.1.2. Remove the engine plastic cover.
1.1.3. Disconnect the ignition coils electrical supply cable and all three coils connectors.
1.1.4. Remove all three ignition coils screws.
1.1.5. Remove all three ignition coils out from cylinder head.
1.1.6. Remove all three spark plugs out from cylinder head (straight forward).

1.2. Back cylinder head bank spark plugs removal:
1.2.1. Remove the inlet manifold out from cylinder head.
1.2.2. Disconnect all three ignition coils connectors.
1.2.3. Remove all three ignition coils screws.
1.2.4. Remove all three ignition coils out from cylinder head.
1.2.5. Remove all three spark plugs out from cylinder head (straight forward).

2. Spark plugs installation

2.1. Refit all in reverse order.
2.2. Spark plugs tightening torque = 2,8 +/- 0,3 daN.m
2.3. Ignition coils tightening torque = 0,8 +/- 0,2 daN.m

Nov 16, 2010 | 2005 Peugeot 405

1 Answer

How do you replace the ignition key switch for a '96 chevy diesel 1 ton 4wd pickup truck?


Ignition Switch Removal & Installation To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the 2 connectors of the multifunction switch assembly out from the bulk head connector.
  4. Detach the key alarm connector from the lock assembly.
  5. Remove the ignition switch mounting screws and the ignition switch from the steering column.
Ignition switch removal/installation gm-08-00-1141.gif

To Install:
  1. Install the ignition switch on the lock module.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Install the key alarm connector on the lock module.
  3. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  4. Install the harness in the original retainers.
  5. Install the steering column trim covers.
---
Ignition Lock Cylinder Removal & Installation To Remove:
  1. Disconnect the negative cable from the battery.
  2. Disable the supplemental inflatable restraint (SIR) system.
  3. Remove the steering column trim covers.
  4. Turn the ignition lock cylinder to the run position.
  5. Using an awl with a bent tip, insert the tip into the access hole of the ignition lock cylinder.
  6. Turn the lock cylinder to start and push down and hold the lock cylinder retaining pin.
  7. Release the lock cylinder to the run position and withdraw the cylinder from the steering column.
Ignition lock cylinder removal gm-08-00-1139.gif

To Install:
  1. Align the slot in the steering column to the tab on the lock cylinder and install the lock cylinder until it locks in place.
  2. Install the steering column trim covers
  3. Connect the negative cable to the battery
  4. Check for correct operation
prev.gif next.gif

Oct 08, 2010 | Chevrolet 3500 Cars & Trucks

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

Ignition switch replacment


Ignition Switch REMOVAL & INSTALLATION The ignition switch is located at the bottom of the ignition key cylinder body. To remove the ignition switch, first remove the ignition lock cylinder.

1993–99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal. NOTE: Always use a new shear pin when installing the lock cylinder.

Jun 25, 2009 | 1998 Volkswagen Jetta

1 Answer

I want to pull it


what year?

1999 electrcial ign switch. Lock cylinder is different

211-05: Steering Column Switches 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Position the LH instrument panel insulator aside.
    1. Remove the pin-type retainers.
    1. Position the insulator.
  1. Remove the LH instrument panel insulator.
    1. Disconnect the courtesy lamp.
    1. Remove the insulator.
  1. Remove the lower instrument panel steering column opening cover.
    • Remove the screws.
    • Unhook the parking brake release handle and position aside.
    • Remove the cover.
  1. Remove the five bolts to remove the instrument panel steering column opening cover reinforcement.
  1. Disconnect the ignition switch electrical connector.
    1. Loosen the bolt.
    1. Disconnect the electrical connector.
  1. NOTE: The ignition key should be in the OFF position.
    Remove the ignition switch.
    1. Remove the bolts.
    1. Remove the switch.
---------------------
SECTION 211-04: Steering Column 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder —Functional Lock Cylinder Removal
  1. Disconnect the battery ground cable; for additional information, refer to Section 414-01 .
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key and turn to the RUN position.
    1. Press the ignition switch lock cylinder release pin while pulling out the ignition switch lock cylinder.

86b3f2f.gif

Apr 25, 2009 | Lincoln Town Car Cars & Trucks

1 Answer

Remove ignition tumbler


lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
    Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.




  1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
  1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.


    0764353.gif

  1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.




  1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
Installation
  1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
  1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
  1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
  1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
  1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
  1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
  1. Connect the ignition switch electrical connector.
  1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
  1. Install the steering wheel. Refer to the procedure in this section.
  1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.

Apr 07, 2009 | 1995 Mercury Tracer

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...