Question about 1997 Lexus LX 450

Open Question

Replace brake light bulb. Do I have to remove the entire lense assembly to gain access to the brake light?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change my driver side back up light? Do I need whole assembly?


Year/make/model?? Most back up lights are designed to have a replaceable bulb. Some you can access from a removable panel in the trunk area and twist the bulb out. Others require the entire lens assembly to be removed for bulb access. The lenses are normally held in place with plastic type screws/clips

Jan 06, 2016 | Cars & Trucks

1 Answer

How to replace rear signal light bulb 2006 Lucerne CX


the lens assembly is help in with three nuts. A 10mm socket will work to remove them.

Simple pull back the trunk liner to gain access to the nuts. Remove the nuts. Remove the lense assembly from the vehicle. Replace the bulb.

airjer995_64.jpg

Apr 26, 2011 | Buick Lucerne Cars & Trucks

2 Answers

I cant seem to find out how to remove the tail light to replace the bulb. what am i missing?


Typically, the entire tail light assembly has to be released from the inside. So you have to remove trim, inside, for access, usually 3 or 4 thumbscrews get released and the whole thing comes out. This set up is much more watertight than the older method of lense removal.

Mar 26, 2011 | 1993 Buick Roadmaster

1 Answer

Can you give instructions to replace reversing bulb in ford focus


the fixing scews for the lense/bulb holder are on the top of the lense just under the boot lid as you open it . once you have removed the screw/s the whole assembly should be loose and you can easily remove it to gain access to the bulbs

Aug 09, 2010 | 2003 Ford Focus

1 Answer

The lower brake light on the driver side is out. What is the method of replacing? Do I have to pull the assembly or can the bulb just be removed?


inside the trunk if you have access to the turn buckle to the bulb remove and replace but usually all the nuts need to be removed to the entire assembly before you can gain access and replace bulb .

Oct 17, 2009 | Hyundai Motor 2005 XG350

1 Answer

How do i change a brake light?


The access for your brake lights is in your trunk, there will be screws that hold the taillight assembly on, remove them to gain access to the bulbs, then twist the socket to remove it, then you will be able to replace the bulb, reassemble in the reverse order.

Aug 22, 2009 | 1995 Dodge Intrepid

1 Answer

Burned out license plate bulb


open trunk,

remove felt liner from rear of trunk, (liner directly behind rear lights in side trunk) should be 4 plastic Phillips head screws. Loosing screws, then slowly peel liner away. You will see 3 nuts on each side, removing these nuts will loosing the rear light lenses, so you can pull the lense away from the body from the out side to gain access to the license plate bulbs. Re-install in reverse order. While in there I would recommend replacing your brake light and reverse light bulb. Hey your already in there might as well do a little preventive maintance.

Dec 12, 2008 | 1995 Lexus ES 300

1 Answer

Replacement of failed RH daylight driving headlight.


part # 9006ST...accessed from back of headlight bucket...unplug connector twist connector at bulb base..do not touch glass on new one...your oils will cook the new bulb

Dec 08, 2008 | 2005 Cadillac Escalade

1 Answer

Replace tail light bulb


The process for changing the tail light bulbs for a 2002 New Beetle in my case a TDI is relatively simple. To remove the lense and gain access to the bulbs you first need to release the lense holder from inside the trunk by completely unscrewing the large plastic wing nut that is under a round plastic panel that's located almost directly behind the rear brake light lense. To gain access to the plastic wing nut remove the round panel by gently prying it off. After this is done you release the lense by using something flat like a dinner table knife to pry and release the clip that holds the lense in place. Locating the clip: The rear fender has two seams that end at the light lense, the inboard seam (the one closest to the hatch)is where you want to insert the table knife to pry the metal clip that holds the lens in place. Gently and carefully insert the knife blade directly at the seam and pry upward to release the lense. Once the clip releases pull the lens the rest of the way and remove the bulbs by turning the bulb holder sockets couter-clockwise. After this is done remove bulbs by slightly pushing down on the bulb and turning it counter-clockwise. The reinstall is reverse of the removal the procedure.When re-installing take care to clock the lense where the metal clip and the lense protrusions end up in the same position as before. Note: you may need to assist sliding the lens retaining clip in with the knife when reinstalling! Good luck

May 15, 2008 | 2003 Volkswagen New Beetle Convertible

Not finding what you are looking for?
1997 Lexus LX 450 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...