Question about 1989 Toyota Camry

1 Answer

I need to find a front clip - 1989 Toyota Camry

Posted by on

  • Dennis Gentz
    Dennis Gentz May 11, 2010

    where are you located?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,865 Answers

Call the junkyards in your area

Posted on Jul 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2005 Avensis sedan front windscreen washer does not work - wipers do still opperate. Where is the fuse for this located and what else could cause this problem?


PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

May 15, 2011 | Toyota Passenger Cars & Trucks

1 Answer

I need to take apart my 4unner grill


There will be one screw to undo, the rest is held in by clips , these are accessable from the front, using a flat bladed screwdriver lift the small tag protruding from the front of the clip, the grille will pop out ( one clip at a time) , leaving the clips behind in the radiator support panel, these come out with a twist and can be clipped back in to the grille before re-installation

Mar 28, 2010 | 1999 Toyota 4Runner

1 Answer

What is the Firing order for my 1988 Ford Ranger XLT 2.9L


1,4,2,5,3,6. clockwise. Standing in front of engine,Looking at front clip to hold cap on, 5,2,4 would be order from right of clip, back to rear hold clip. On left of clip, 3,6,1 would be order from front to rear clip.

Dec 26, 2009 | 1988 Ford Ranger

1 Answer

How to remove the front door of a 2000 toyota sienna


  1. Remove the phillips screw that holds the door handle trim piece (under the door handle)
  2. Remove the phillips screw at the upper front under the small round trim cap. Pry gently around all sides of the cap, prying a little more each time.
  3. Remove the arm rest by forcing it up with a screw driver. Start with the end towards the front of the car. Start prying at the front edge and next to the door panel. The arm rest has two clips (one at front edge and one about three inches back. Once the two clips are loose the arm rest flips towards you which unhooks the back two prongs.
  4. Pry off the control panel. This trim piece has a metal clip that you need to press from the front edge. There is a small indent to allow a small screwdriver. Don't use a screw driver! Use a thin putty knife, but a scredriver will work. There is a lip that the knife will catch on and release the trim. The back of the trim has a fixed clip, so unless you release the front clip it ain't gonna budge! Then unplug the attached wires.
  5. Now remove the 2 screws that appeared once the arm rest is off. I think that's all the screws. Pry the bottom of the panel away from the door starting at the bottom back corner (you will feel where there is resistance) and the plastic retaining clips will pop loose one after the other.
  6. Your panel should now be completely loose on both sides and the bottom, held on only by the top lip (that is supposed to lift off) and the door handle trim
  7. The door handle trim is a little tricky but once you know its not that hard. First of all its held it place by two clips. One is directory over the lock switch and one directly under it. Carefully pry underneath the trim in both of these location and twist the screwdriver to pop off the clips. There is still a hook clip nearer the front of the trim so to pull off the trim you have to kind of pop out the two clips while pulling towards the rear of the car since the hook clips slides out towards the rear.
  8. Once that is off its just a matter of lifting the whole panel up until it unhooks from the top of the door.

Jun 01, 2009 | 2000 Toyota Sienna

2 Answers

Grill removal


the lower clips are pushed down with a long screw driver from the front , when the grill is removed the clips need to be removed from the vehicle and put in the grill then push the grill in

Apr 18, 2009 | Mitsubishi Pickup Cars & Trucks

1 Answer

How do you remove the front clip of 02 x type jag.


That Means the Entire Front End. Please Rate my Solution, I need all the Help that I can Get! Thanks!

Jan 29, 2009 | 2003 Jaguar X-Type

1 Answer

Front fender removal


Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

808b156.jpg

Nov 20, 2008 | 2005 Chevrolet Equinox

1 Answer

Remove inside door panel on 1995 lesabre


These are not too difficult to remove, you just need to know where the hidden fasteners are. The usual plastic clips hold the panel around the sides and bottom, and need to be gently pried up, ideally with the tool designed for this. At the back of the armrest there is a reflector, a sort of triangle shaped thing, which must be removed, by working a slim screwdriver in at the top, to push down on the clip that holds it. This clip is sort of sawtooth shaped, bends down when installed, and pops back up when in place. When it's out, you'll see a 10mm bolt which secures the door panel to a bracket on the door, looking straight in through the hole. Remove it. The power window switch assembly needs to be removed to access the other two of these lag bolts. There is a spring clip at the front of the switch, you need to work a tool (screwdriver or similar) GENTLY in between the front of the switch and the armrest, and push this clip backward. The front of the switch can be raised, and the switch slides forward and out.There are two bolts holding the panel to a bracket looking down through the opening. After that, it's just the usual clips. Good luck!

Nov 15, 2008 | 1995 Buick LeSabre

1 Answer

Front headlight Removal


This is not an easy task, there are two bolts and a clip that need to be removed, then you need to take the headlight assembly completely out of the frame of the car and pull the light bulb out of the back. The clip on the front took two of us to remove. One holding a screwdriver to the clip while the other moved it side to side til it came free. Good Luck. The light bulb has a stupid *what looks like a paperclip bent out of shape* around the back of the socket, and when removed can spring away so be cautious!

Nov 05, 2008 | 2000 Chevrolet Prizm

Not finding what you are looking for?
1989 Toyota Camry Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...