Question about Chevrolet Astro
I need a diagram for replacing exterior door handle
You will need to get the door panel off the inside,undo the linkages and the remove the nuts holding the handle on.
Posted on Jul 28, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door
Posted on Oct 23, 2009
remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle
Posted on Nov 14, 2008
If you remove the inner door panel of the door there will be plastic weather shield covering most of the door. Use a hair dryer or heat gun to heat the weather shield up and slowly peel it away. There will be 2 (10mm I believe) bolts on the inside of the door panel to release the handle (have someone catch it from the other side). To re-install simply connect he handle rod and 2 bolts then place the door panel back on and your done. A word of advice is be gentle with the door panel so not to damage the door pins or crack the plastic. Taking your time can be fun when learning a car ;).
Posted on Aug 17, 2008
I'm assuming that you have the coupe not convertible since I've had same problem with my 97 Dodge Avenger and this is quite common from what I have heard. The handle is held in place by two 10mm bolts. One is easily accessable, located right beside the handle with the door open. The other is a little harder to get at. The first thing you need to do is remove the inside door cover, held in place by four screws and push in clips along the bottom that pull out easily. Two of the screws are visible and in the top corners of the door panel. One screw is located behind the inside handle and once removed the moulding comes off quite easily. The other screw is in the hand hold where you pull the door closed and has a small plastic cover over it. If you have power windows you are able to disconnect the switches once the panel is off. If manual windows, the handles are usually held on by a clip that can be pushed off with a screw driver allowing you to pull of the crank handle. The window needs to be in the closed position so you can access the ONE 10mm bolt holding the outer door handle. Once the interior door panel is off, if any clips remain in the door, take them out and put them where they should be in the door cover it won't go back together properly if you don't. Now you'll need to pull down the corner of the plastic covering the door, don't remove all the plastic just enough to allow access to the bolt. I used a small rachet to get it out. It is in a stupid spot with not much room but is doable. Once out, the handle is only being held by the lock rods to the handle and lock cylinder. The lock cylinder is held by a retaining clip which can be slid off allowing the cylinder to be pushed out. The other rod connected to the handle has a plastic clip on it holding it in place. This can be opened with a small screwdriver. Once opened the rod will come out easily and the handle should come off the door. The only problem reinstalling, that I had, was reconnecting the rod to the handle and found that if you unscrew the door latch, the whole mechanism can be moved down, giving you more freedom to work with the rod. You might want to do this before fighting with the clip holding the rod in place, just a thought as I got mine apart in 20 min. Installing the new handle is quite easy, just attach rod to the handle FIRST before anything else. Once the handle is back on the door the lock cylinder can be pushed back in, it just gets in the way if you put it in the handle right away. Hope this is of some help.
Posted on Oct 05, 2008
Tips for a great answer:
Feb 22, 2014 | GMC Cars & Trucks
Oct 29, 2013 | Cars & Trucks
Oct 22, 2009 | 2003 Nissan 350Z
Aug 02, 2009 | 2003 Kia Rio
May 30, 2009 | 1997 Toyota Camry
Apr 25, 2009 | 2001 Ford Escape
Dec 14, 2008 | 1997 Toyota Camry
Nov 14, 2008 | 1998 GMC Safari
Sep 24, 2017 | Chevrolet Cars & Trucks
1,107 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: