Question about 2002 Mitsubishi Galant

1 Answer

Can't locate the camshaft position sensor for a v6 3.0L

Please e-mail me ASAP. I have no car to use.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 305 Answers

Well different engines have the sensor in diffreent places. 2.4l on front between timing belt and pulley,2.4l dohc i think is inside distributor.so i hope you get the idea,service manual is needed for this,purchase one at autozone or advance and life will be a lot simplier.
Actually, 2001 2.4L SOHC is on the right side of the engine. "Standard" time is 0.3 hours but I just replaced mine in about 10 minutes. Make sure you detach the intake hose in the front by the airbox and loosen the rear clamp and tilt the hose up out of the way. Requires removing the cable clamp bolt for the ??? cable on the top front right side of the valve cover. And it helps to remove the cable guild bolt holding the cable next to the wires for the CPS itself to get wiggle room to remove and reinstall it. Once you get the intake hose out of the way you should be able to see what's going on.

Posted on Jul 27, 2009

  • jim galbraith
    jim galbraith Jul 27, 2009

    if this helps, please remember to leave a rating for me....

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor located on a 2005 cadillac deville base model?


LOCATION
The camshaft position sensor is located on the rear cylinder bank in front of the exhaust camshaft. The camshaft position sensor extends into the rear cylinder head and is sealed with an O-ring.


26349435-oucqd2i3pucu3s1utbyq1gmo-1-0.gif

Nov 10, 2016 | 2005 Cadillac Deville

1 Answer

Locate camshaft sensor 2008 3.6l malibu


Which one ?
Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake

Sep 02, 2016 | 2008 Chevrolet Malibu

1 Answer

Where is the camshaft position sensor located in a


The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Oct 10, 2014 | Cars & Trucks

2 Answers

Where is 2003 ford focus camshafts position sensor


Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

1 Answer

Camshaft position sensor


ON THE 4 CYLINER ENGINE CAMSHAFT SENSOR LOCATED AT THE LEFT DRIVERS SIDE OF THE TIMING COVER. THE V - 6 ENGINES CAMSHAFT POSITION SENSOR LOCATED AT THE FRONT OF ENGINE BLOCK BELOW THE POWER STEERING PUMP.

Aug 28, 2012 | 2000 Oldsmobile Bravada

1 Answer

Where is the crankshaft and camshaft position sensors located on a 1996 chevy cavelier and are there any diagrams available for replacing them


The crankshaft sensor is located just to the side of your ignition coil pack on the engine block. The camshaft sensor is located on the back of the engine, just to the left of the oil filter. I would HIGHLY suggest having a qualified technician do this job for you. There is only one 10mm head bolt holding the sensor into the block, but these sensors are know to freeze into the engine block and break leaving a part of the sensor in the engine. If you attempt this yourself, be sure to rotate the sensor once the bolt is removed, and pull GENTLY. If it breaks, your in for a large repair bill.

Aug 14, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

Check engine light is on. Code is related to camshaft position sensor. Where is the sensor located on a 1999 BMW 323is?


This is a normal problem and you need to replace it asap. The camshaft position determines when top dead center compression of the #1 cylinder occurs and the convertsit into a pulse signal that is sent to the pcm , then the pcm uses it to determine the correct injection sequence.

May 25, 2009 | 1999 BMW 323 Series

1 Answer

How do I change Camshaft position sensor


THE CAMSHAFT SENSOR IS IN THE DISTRIBUTOR.

May 01, 2009 | 1996 GMC Jimmy

1 Answer

Need to know where cam position sensor is located and if its easy to repair at home


Please E-Mail me at simard2@comcast.net and I will be able to send you an E-Mail with the step by step direction on where the Camshaft Position Sensor is and how to remove it! The reason why I am asking you to E-Mail me is because I cannot enter all the information in the solution box, it is too big.

Thank you for using Fix Ya!

Feb 18, 2009 | 1997 Toyota Camry

1 Answer

Location of camshaft position sensor on a 2001 Hyundai Elantra wL


The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.

Dec 26, 2008 | 1998 Hyundai Elantra

Not finding what you are looking for?
2002 Mitsubishi Galant Logo

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...