Question about Ford Ranger

1 Answer

Water pump is out. How do I get id out to replace

Water pump is out opn my 1993 Ford Ranger. How do I get it out to replace it?!!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Is it a 4 or a 6 cylinder engine, well you need to take off the fan clutch if it has one if not skip the step; its just 4 screws, then take off the acc belt, then take off the hose that goes from the radiator to the water pump; at the water pump, then remove the screws holding the water pump; make note what screw goes where some screws may be different sizes; in some 4 cyl 2.3L engines the timing belt cover has to be removed to remove the water pump, then remove the water pump, scrap off all gasket residue from the surface of the engine, take automotive silicone gasket maker and apply a small amount to the new water pump and level it out then put the included gasket over the silicone, then let it set for a couple of minutes, apply a bit more of silicone over the gasket and again let it set then replace the water pump, replace the screws and tighten all of them snug then go back and torque them between 20 and 25ft lb, replace the water hose, replace timming belt cover if removed, replace acc belt, and finally replace the fan clutch and your all set i hope you can get the job done

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Temperature gauge goes well past halfway when outside temp is above 80 degrees, and A/C on.


I would start with checking the fan clutch if thats fine do a completed cooling system flush and replace the thermostat if you are still having problems replace the water pump

Jun 01, 2011 | 1993 Ford Ranger SuperCab

1 Answer

How to replace the water pump on a 1984 ford ranger 2.8 litr


I just did one on a 94 "almost identicle engine"

This is the way I did it:

drain coolant-remove upper radiator hose-loosen fan bolts '4 bolts attaching it to the water pump'-remove serpentine belt-finish uninstalling the fan- remove 2 bolts securing the fan shroud to the radiator and it should slide out with the fan-remove pump 'be sure to clean the mating surface of the block before sealing with silicone and gasket to ensure it doesn't leak'

reverse the process for installation.


NOTE: if I were you, id replace the timing belt while your in there since the timing cover is nearly impossible to get off without doing this same procedure.

Good luck.

Feb 09, 2011 | 1984 Ford Ranger

1 Answer

1993 3.0 FORD RANGER WILL NOT STARTA FTER ITS BEEN RAN. AFTER A COUPLE OF HOURS COOLING DOWN CRANKS AND RUNS FINE. REPLACED FUEL PUMP RELAY FUEL FILTER COIL.


it could be as easy as the raidiator temp sensor...
But could as easily be a fuel pump going bad.
The fuel pump is an easy one to do... as it is located right below the drivers side door on the frame... and has easy clips to unclip...
I would buy a new filter first though... it is just as easy... and in the same spot...

Oct 06, 2010 | 1993 Ford Ranger SuperCab

1 Answer

My Ford Ranger's water pump went out and I don't know how to remove it. All the ''MacGyver's'' here have not seen the pump so hidden.


go bye a hanys re pair book . you can get them at the auto parts store . that will show and tell you how to re place your water pump

Jul 27, 2009 | 1993 Ford Ranger SuperCab

2 Answers

Cranks but won't start,new fuel pump,no power going to pump


look at inerata reset switch check for power at the switch

Jun 23, 2009 | 1993 Ford Ranger SuperCab

1 Answer

1993 ranger 4 cyl.runs fine then wont restart for couple of hours


lisen for the fuel pump to run when it acts up. if u cant hear it then replace the fuel pump relay

Dec 21, 2008 | 1995 Ford Ranger Supercab

1 Answer

Water pump


you have to go to an autozone or simalar to rent ,there is two wrenches you need,the short wrench you use with a breaker bar and hold the waterpump pulley and the longwrench loosens the clutch hub nut

Jun 27, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...