Question about 2002 Audi A6

1 Answer

2002 audi quatro A6 2.7T. How easy is it to replace the front brake pads??? Any trade secrets to make it simple?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Easy, just nuts n bolts! when u get caliper off compress piston so u can get the new pads in n tighten it back up

not hard at all

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's wrong I just changed my rear pads on my 2008 Mercedes c-300 and after driving about 200 feet. The BRAKE Ebs, Abs, and Esp inoperative. It initially was just brake pad wear


DIYer? There is probably a "reset" in the computer system when pads are changed. It may be an MB trade secret for the prevention of liability issues.

May 05, 2015 | Cars & Trucks

1 Answer

2002 audi a4 e-brake won't release


It sounds like your rear brake pads are frozen to the rotor, or a small amount of rust is causing them to stick. Put all the tires back on and try to drive a few feet, that usually pops the pads off the rotors.

Dec 26, 2012 | 2002 Audi A4

2 Answers

Replace brake pad light on, how do you reset it?


you need to replace the pad wear sensor when the pad wears down it wears the sensor and the sensor needs to be replace if you look at the sensor you can see the wire on the sensor wears threw

May 19, 2012 | 2009 Audi Q7

1 Answer

Ho do i replace my a4 2004 front brake pads


IT IS VERY EASY TO REPLACE FRONT PADS IF U WANT ME TO WALK U THROUGH IT REPLY BACK EMAIL BIGGSONNY@GMAIL.COM

Apr 26, 2010 | 2004 Audi A4

1 Answer

2002 Audi A6 3.0 V6 not a Quatro. DIY oil and


yes you will need to use a jack to jack up the front end the filter and drain plug are next to each other

Nov 03, 2009 | 2002 Audi A6

1 Answer

Right side turbo noisy and leaking oil, audi allroad quatro


yes the whole subframe needs to be dropped as an assembly to do this job..2.7t is an awesome engine but not very user-friendly to work on.

Aug 15, 2009 | 2002 Audi allroad

2 Answers

Wat tool do i need to remove front and back brake calipers so i can replace brake pads on a audi a4 2002 2.0 se


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!! Please Rate my Response! Thanks!

Aug 01, 2009 | 2002 Audi A4

2 Answers

Need to replace front brakes. is it hard to do


ya gotta be careful if she has antilock or air sensors stuff will break easy an iz EXPENSIVE call auto part store may have instruct. online for ya

Jul 28, 2009 | 2001 Audi A4

2 Answers

In my 1999 Audi A6 Quattro the BATTERY Went out


You would have to go to the dealership unfortunetly.

Jun 15, 2009 | 1999 Audi A6

Not finding what you are looking for?
2002 Audi A6 Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14184 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...