Question about 2002 Dodge Caravan
Take tire off, remove drum , hammer out old one. with nut and spacers turn nut to pull stud in hole.
If vehicle has rotor. remove tire, remove brake caliper, remove center axle nut, remove rotor. hammer out old. install new one
Posted on Jul 27, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Broken lug stud on rear wheel.
It appears from the excellent picture that the stud has to be spun to line up the half moons at the rear of the stud.Use two thin nuts locked together so you can spin the remaining stud to line up with reliefs in back of the retainer.
Posted on Oct 18, 2008
SOURCE: wheel studs or bolts
Hello Miguel Thank you for using FixYa.com my name is David I hope this Helps you out.
Studs often get damaged from overtightening or from cross threading a nut on the threads. A damaged stud is replaced by unscrewing it from the part and installing a new one of the exact same size.
Stud replacement can be difficult because the stud has often been in place for a long period of time. There has been constant heating and cooling, corrosion, and rust buildup between the stud threads and the internal threads of the part. These factors combine to make some studs very difficult to remove.
The first step in stud removal is to use penetrating fluid to remove the corrosion to free the stud from its mating threads. Soak the area of the threads with penetrating fluid. Allowing the fluid to soak into the threads overnight will make it easier to remove the stud.
Before removing the old stud, measure the distance it sticks up from the surface. This measurement will be needed later when installing the new stud. Use a 6-inch scale to measure from the part surface to the top of the stud. Write the measurement down so it can be referred to later.
A stud remove is used to remove studs. It is installed over the stud. The jaws on the stud remover grip the outside of the stud. A wrench fits on the stud remover and allows the technician to rotate the stud in a counterclockwise direction to remove the stud.
If a stud remover is not available, a stud can be removed with two nuts. Locate two nuts that are the correct thread size. To thread onto the stud. Start one nut and thread it all the way down to the bottom of the stud. This nut will be the drive nut. Start another nut and thread it down until it contacts the first nut. This is called the jam nut.
Put a wrench on the bottom drive nut and hold it in place. Put another wrench on the jam nut and tighten, or "jam" it against the drive nut. The jam nut will now hold the drive nut in position on the stud.
Now put an open-end wrench on the bottom drive nut. Turn the nut in a counterclockwise direction. Turning the nut in this direction causes it to want to unscrew the stud. Instead the forces cause the stud to unscrew.
When the old stud is out, inspect the internal thread. If it appears rusty or damaged, clean up the thread by running the correct size tap through the threads as previously explained. Compare the new stud with the old one. The studs should be exactly the same thread size and the same length.
Check the vehicle's service manual to determine if the threads of the new stud should be coated. If the stud should be locked in place and not easily removed, you may need to use a threadlocking compound or threadsealing compound. Threadlocking compounds are on studs and other fasteners when vibration might cause them to unscrew. Thread sealants are used when a stud extends where liquids, such as oil or coolant, could get on the fastener.
Antiseize compound is used on the stud threads to prevent the stud from reacting with the metal on the internal threads. If this happens, the stud could stick or seize. Antiseize compound prevents this reaction and makes the stud easier to remove the next time.
After the new stud is properly coated, it can be installed. Start the stud by hand, making sure it enters the threads securely. Turn the stud in as far as possible by hand before using any tools. Then use two nuts as described earlier to drive the stud into the part. Use the depth measurement made on the old stud to be sure it is driven in the correct depth.
Look for More Parts A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z Related Parts: Wheel Nut
Posted on Nov 06, 2008
SOURCE: Changing Rear Rotor Studs
These studs are 'pressed' in at the factory, and really should be replaced by a professional.
At the very least you would need a shop press and/or apowerful air compressor and impact gun.
First, are they in the rotor or the hub. (I don't know if this is a4x2, 4x4, etc.) If they are in the hub itself, this MUST be done by a professional. If they are in the rotor, I would seriously consider replacing the rotor, which in some cases can actually be cheaper.
If you don't want to replace the rotor, please take it to a qualified mechanic, parts store (some do this type of work regularly), or machine shop.
Although I could describe how to do it, an improperly seated wheel stud could have tragic consequenses. Good Luck!
Posted on Dec 03, 2008
SOURCE: broken wheel stud
1. get new studs and nuts
3. remove caliper at bracket to spindle connection(2 18mm bolts?)you may need to remove caliper from bracket,but not always nessacery. Or remove drum,then to #5
4.remove rotor,will need a hammer, tap inbetween studs dont wreck good studs and see if new studs can be installed without removing parking brake shoes. If there is no clearance to get new stud in you will need to remove shoes.
5.Pound out old studs place new stud in hole use a washer on outside then put a nut on and tighten to install stud, A air gun or some type of impact tool will be very helpful. Check to see that stud has enough threds to pull stud all the way thru ,add more washers if nessecary dont let the nut run out of threds it will **** to get back off and wreck new stud.
6. if you dont have air gun or feel comfertable removing brakes bring it to a reputable garage, shouldnt cost more than $70+ parts to get all new studs put in on one wheel.
Posted on May 17, 2009
SOURCE: Rear tire lug bolts
You have to remove the tire/wheel assy. remove the brake drum, you will see the spindle with the bolts there. punch out the broken bolts install new buy pushing thru the hole.Find some regular nuts that will fit over the stud, put your new nuts on and tighten up till flush in back.
Posted on Jun 28, 2009
Tips for a great answer:
Jun 24, 2016 | 2003 Mitsubishi Outlander
Oct 22, 2011 | 2004 Ford Explorer
Oct 28, 2009 | 2004 Toyota Corolla
Sep 25, 2009 | 2005 Ford Focus
Jul 08, 2009 | 2009 Chrysler Town and Country
Jun 13, 2009 | 2005 Dodge Caravan
Jun 07, 2009 | 2003 Chevrolet Cavalier
Feb 10, 2009 | 1998 Toyota Corolla
Oct 04, 2016 | 2002 Dodge Caravan
141 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: