Question about 1997 Dodge Ram 1500 Club Cab

1 Answer

WHEEL HUB REPLACEMENT

I NEED INSTRUCTIONS ON HOW TO REPLACE THE RIGHT FRONT WHEEL HUB ON A 1997 DODGE RAM 1500 PICKUP TRUCK

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 334 Answers

Go bye a hany repair manual at your auto parts store that will show every thing you need to know

Posted on Aug 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2001 Dodge Ram 1500 5.2 2WD, I just found


This is a very simple job to do. Raise the front of truck off the ground,block the rear tires. Using pliers and a hammer,remove the grease cap from hub. Remove the cotter key and nut from axle,pull out slowly and remove outer bearing. then remove hub from axle. To remove inner bearing ,prop hub on a board and use a large punch to drive out bearing and seal. Clean out inside the hub and install new bearing and seal. Replace all parts in the reverse as you took them off. Hope this will help you.

May 14, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

On my 2001 Dodge Ram 1500 5.2 2WD, I just found out that I have to change the front hubs if I want to replace the front wheel bearings. How insane is that! What can I do to have a front hub that I can...


buy an older truck to answer question all newer model vehicles have gone to a hub/flange bearing assembly these bearing setups handle loads without or very minimum variance, when you go into a cornering situation these bearing setups give you a steady and consistent track thus a better handling vehicle now instead of cleaning and repacing tose old cone and race style bearings you just unbolt hub assembly and any related abs sensors and bolt on new

Mar 24, 2010 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How to determine if 97 Ram 1500 has 2- or 4- 2wheel brakes? Need info for wheel bearing replacement.


on 1997 dodge ram 1500s you can look at the back of the front brakes and if you do have 4wheel abs you will have a brake line and an electrical line running tto the brake caliper. you can also look at the master cylinder, on the right side of the power brake booster (if youre looking from the front of the truck) there will be a metal brake distribution block if it has 2 lines running out of it you have 2 wheel abs...4 lines means 4 wheel abs

Oct 23, 2009 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Front axle hub torque


Ram 1500 Pickup ...... 175 foot lbs. Then tighten until the cotter pin can be inserted. I had the same problem. I had to replace the inline check valves and I also had a bad hose. The check valves are not expensive.

Jul 29, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

Clicking noise in front end 2001 dodge ram 4x4


the ansew i found is replacing the seal around the joint and from both end removing it and cleaning it out i had rocks in mine from going threw water and mud ita a all day deal but a twenty doller fix axle shaft oil seal is all i had to replace

Apr 05, 2009 | 1997 Dodge Ram 1500 Club Cab

1 Answer

How do you change the wheel bearings in a 2003 Dodge Pickup


Is the truck a 4x4? If it is you will have to replace the bearing assy. which will most likley be diffucult without the right tools.the bearing bolts into place,but the hub assy are known for rusting into place and being very hard to remove.

Mar 29, 2009 | 2004 Dodge Ram 1500

2 Answers

2000 dodge ram 1500 front end clicks in 2wd and bucks in 4wd


Sounds like either your hub assembly or front axel universals.

Mar 21, 2009 | 2000 Dodge Ram 1500 Truck

1 Answer

HOW DO I REMOVE ANS INSTALL WHEEL HUB 2002 DODGE 1500 PICKUP!WHAT


4x4 has 3 bolts in back of knuckle take them loose and tap on them to force the hub out of the knuckle

Jan 19, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

Wheelbearing replacement


Hello
Welcome to FixYa
the front wheel bearing is a hub unit.
need to remove the tire,brake caliper, rotor, the 34mm nut in the axle, then there is 3 bolts that hold the hub to the spindle, those come off then the hub comes out,reverse to install.
RD

Jan 12, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...