Question about 2004 Nissan Quest

1 Answer

Is it true that the whole engine needs to be disaasmbled to reapair the timing on a 2004 nissan quest

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

The oil pan will need to be removed to remove the front cover. It would be easier to remove the engine to replace the timing components. Only the oil and front cover needs to be removed.

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel cutoff switch in a 2004 nissan quest? The car is not transferring the gas through the plump. It did yesterday. And now you cannot hear the plump. I just want to turn off the fuel cutoff...


i know that the previous gen quest had the fuel inertia RESET switch on the driver side kick panel...

fuel is cutting off via the ECM for your generation though

"If the engine speed is above 1,800 rpm with no load (for example, in neutral and engine speed over 1,800 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off varies based on engine speed. Fuel cut will operate until the engine speed reaches 1,500 rpm, then fuel cut is cancelled."

http://www.nicoclub.com/FSM/Quest/2004_Quest/ec.pdf

EC 33

do you have trouble codes ?

Mar 03, 2015 | 2004 Nissan Quest

1 Answer

List of interference engines


Hi, I believe the VG series of engines are interference engines, meaning if the valve timing is lost the valves will be damaged! Regards John

Jul 22, 2014 | 2004 Nissan Quest

2 Answers

My 2004 Nissan quest and starts but when I'm


your timeing is out might need new timeing belt

Mar 24, 2012 | 2004 Nissan Quest

1 Answer

I need to reapair the rear main seal on m1994 nissan quest. any help please?


You will have to remove the transmission to gain access to replace that rear main seal.

Jan 26, 2011 | 1994 Nissan Quest

2 Answers

Where is the camshaft positioning sensor located in the 2004 nissan quest


Your 2004 Nissan Quest is most likely to be equipped with a 3.5L V-6 engine. This engine has 2 Cam (PHASE) sensors. One is located in the back of each cylinder head. You must remove your intake air duct to see them.

Oct 17, 2009 | 2004 Nissan Quest

2 Answers

Oil consumptiom


Figuring off of national standards thata gasoline engine is allowed to burn 1qt. of oil every 2,000 miles tthey would be correct.But That is not to say for that particular engine providing that oil has been changed every 3000 miles,There could be other problems contributing to your car,for instance cklogged pcv valve,leaking injectors or fuel preasure regulator both can cause fuel contamination to engine oil (Dillution) Thins oil too much,or overheat condition,or failed cat convertor.With this in mind talk with another Nissan dealer if only by Phone.

Jun 19, 2009 | 2004 Nissan Quest

3 Answers

2004 Nissan Quest front control arm bushing replacement.


Sorry guys not a solution but I too have an 04 Quest, which supposedly has worn controller arm bushings and Nissan says I need both controller arms replaced. For a total of $950!!! I was told that they need to replace the whole arm and cannot replace only the bushings. Now reading the posts on this site I find that to be untrue. Seems all I need to spend is anywhere from $25 to $35 per bushing.

Nov 30, 2008 | 2004 Nissan Quest

1 Answer

Bad left lower ball joint 2004 nissan quest


most of these ball joints can be installed by themselves however since the control arm are so light it is unsafe just to do the balljoints still in order to replace the control arm you dont need to compress any springs just take it apart and put a new one in.

Nov 14, 2008 | 2004 Nissan Quest

Not finding what you are looking for?
2004 Nissan Quest Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...