Question about 2001 Jaguar S-Type

1 Answer

Shifter alignment cable is out of place, how do i fix it ? If I put the car in drive it roles backwards. I have to drive with the car on 4.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jaguar Expert
  • 489 Answers

To Adjust : 1- Unclip parking brake boot. 2- Detach the center console upper section. 3- Disconnect cigar lighter electrical connector. 4- Remove te center console upper section , disconnect the transmission mode and traction control electrical connectors 5- Move the selector lever to position "R" 6- Loosen the selector cable lock nut 7- Detach the selector cable. 8- Raise and support the car. 9- Move the Rotary position switch to the "R" position , so that it matches the lever. 10- Lower the car. 11- Connect the selector cable (Do not tighten selector lever lock nut) 12- Move selector lever to "D" , hold the selector lever applying light pressure and fingure tighten the rear lock nut , then fingure tighten the front lock nut 13- Now move the lever to different gear positions , ( when "D" is selected , make sure it sits as close as possible to the "D" and "4" position in each corner. 14- Tighten selector lever lock nut. 15- Install center console upper section. (connect the transmission mode and traction control electrical connectors) 16- Connect the cigar lighter connector 17- Install the center console upper section. 18- Clip together the parking brake boot.
And you are done , I know it looks hard but it is not , read through my instructions and understand it and all will be easy to do. Good luck , hope it helped :)

Posted on Aug 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put in low four wheel drive shifter won't go back to four wheel high


check your lever shifter alignment,and check also solenoid shifter,and check also transfer case alignment it might be transfer case bolt support.

Nov 03, 2014 | Cars & Trucks

2 Answers

How do I fix my shifter on my 2004 Ford Freestar Van?


The cable HOUSING has become loose from the anchor point. Get under with a hammer and a pliers and put back in place. Then persuade it to stay in place.

Sep 07, 2014 | 2004 Ford Freestar

1 Answer

Saturn shifter cable


They have replacment shift linkage bushings on ebay, but a bit pricey. The bushing can be a Easy fix though if you have tools and time.
1st drill out the ball at the end of the linkage, this is the one your broken bushing use to ride on. Place a 3/8 inch bolt thru the drilled hole. Slide a piece of 3/8 inch heater hose over the bolt ( this is what the linkage ring rides on ) put a rubber gromet or rubber washer that has a hole big enough to fit over the heater hose on each side of the linkage ring ( oh and dont forget the lube - regular grease will eat rubber so use good judgement). put a washer big enough to keep your gromet or rubber washer from falling off, and then a lock nut, and I cannot stress the fact that it has to be a lock nut. DO NOT tighten the living **** out of everything, that little linkage ring is plastic after all just tighten it "lightly snugish" and just make sure your lock nut can't be un-tightened by hand. I hope all of this makes sense, anyway total repair cost- one hour of my time, about $4 of parts at the local auto parts store

Jan 27, 2014 | Cars & Trucks

1 Answer

Adjust shifter linkage


2002 neon is cable shift and usually the cable fits in brackets. there is alignment pin in shifter base. put a pin in to hold it in neutral position until you have the cables in place and all brackets tightened then remove the alignment pin and put console back together.

Jun 03, 2013 | 2002 Dodge Neon

1 Answer

The gear shifter feels like its not in place


linkage needs ajust--getta haynes manual atta parts store

Aug 25, 2012 | 1990 Ford Escort

1 Answer

96 probe will not stay in place when in park, will not reverse or drive


sounds like the cable shift has come apart but without my head under the bonnet i honestly couldnt say ,never knew they made a auto version of this car as never seen one here

Mar 02, 2012 | 1996 Ford Probe

5 Answers

Shifter is stuck in park


Billettechnologies.com sells a replacement cog to put your shifter backinto action. Their part replaces a factory plastic piece...no wonderthese are failing at a fast rate.
Here is the LINK to make this change out of parts...

Sep 22, 2009 | 2005 Dodge Magnum

6 Answers

Mazda 6 shifter cables broken


I had this same issue last week with my 2005 Mazda 6 Manual.... I feel your pain. About $275 for the new Cable and another 300 to install it.

Jun 22, 2009 | 2005 Mazda 6

Not finding what you are looking for?
2001 Jaguar S-Type Logo

1,458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...