Question about Toyota Cars & Trucks

Open Question

Torque valu toyota 22r rod bolts - Toyota Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76164 Answers

SOURCE: 2005 Tucson

camshaft sprocket bolt 58-72 ft. lbs. crankshaft pulley bolts 108-132 ft. lbs. crankshaft pulley center bolt 80-94 ft. lbs. cylinder head bolts cold engine 65-72 ft. lbs. warm engine 73-80 ft. lbs. cylinder head rear cover bolts 69-86 in. lbs. flywheel/Driveplate bolts 94-101 ft. lbs. intake/Exhaust manifold nuts/Bolts 11-14 ft. lbs. jet valves 13-16 ft. lbs. main bearing cap bolts 36-39 ft. lbs. oil pan bolts 51-69 in. lbs. oil pan nuts 43-60 in. lbs. oil pan drain plug 33 ft. lbs. oil pump cover bolts 72-84 in. lbs. oil pump relief valve plug 29-36 ft. lbs. oil pump sprocket nut 25-28 ft. lbs. Rear oil seal retainer bolts 84-108 in. lbs. rocker arm shaft bolts 14-15 ft. lbs. rod bearing cap nuts 23-25 ft. lbs. silent shaft sprocket nut 22-28 ft. lbs. spark plugs 15-21 ft. lbs. thermostat housing-to-Engine bolts 86-114 in. lbs. timing belt tensioner bolt 32-40 ft. lbs. valve cover bolts 43-61 in. lbs. water pump-to-Engine bolts alternator brace bolt 14-20 ft. lbs. all others 9-11 ft. lbs. water pump pulley bolts 72-84 in. lbs.

Posted on Sep 08, 2008

Ad
  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

terseo
  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

Dirt Dobber
  • 253 Answers

SOURCE: need torque for a 2000 Toyota Celicia GT 1.8L

Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Posted on Mar 19, 2010

tburtk
  • 158 Answers

SOURCE: i need torque specs for a 2004 dodge cummins 24

http://www.dieseltruckresource.com/dev/index.php

I suggest this website for your dodge truck needs.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque value


Here are the torque specs you requested:
MAIN BRG CAPS= 29FT/LBS THEN TIGHTEN AN ADDITIONAL 90 DEGREES in sequence(two step process)
ROD BEARING CAPS= 18 FT/LBS
CYLINDER HEAD BOLTS= 29FT/LBS + 90 degrees + another 90 degrees in sequence from the center out ward, (3 step process).
Please let me know if you have any questions.

Always happy to help.

Aug 22, 2015 | 2006 Toyota Hilux 2.0

1 Answer

I need torque sequence for rod bearing caps


There is no sequence for the rod caps Since there are only 2 bolts per cap you only have to snug up each bolt then apply half the listed torque value to each cap bolt. then continue back and forth on them until the end torque value is applied to both bolts.

Apr 29, 2015 | 1996 Pontiac Bonneville SE CA Value

1 Answer

Hi i hav a 1990 toyota with the 3vze 3.0 v6 sohc 12 valve i need the rod bolt torque


The connecting rod nuts for these engines use a combination torque, then turn method to achieve the proper clamping load. First the nut is torqued to 18 lbs.ft., then turned an additional 90°. It is possible for the rod bolt to slightly turn inside the connecting rod during this process, causing the final torque to be below specifications. The nut must be turned 90° relative to the bolt, not the connecting rod.

Mar 23, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

89 toyota pickup torque specs. for flywheel and clutch bolts 22re 4x4


Thoroughly clean the flywheel bolts. Coat the first 3 or 4 threads of each bolt with sealant. Install the flywheel, aligning the previously made marks. Install the bolts finger-tight.
Tighten the bolts in a crisscross pattern and in several passes to the correct tightness:
  • 22R/22R-E manual trans-80 ft. lbs. (108 Nm)
  • 14-20 ft-lb for the clutch cover and
  • 50 ft-lb for the transmission mounting bolts.
Since you have the flywheel off, be sure and inspect the rear main seal. Now might be a good time to replace it. Be sure the rear flange of the flywheel is clean before re-install.
Be sure to inspect or, better yet, replace the bronze pilot bushing. I f you don't know how to get it out leave a comment. J


Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is really appreciated for the FREE answering of your question.

Feb 14, 2011 | 1989 Toyota Pickup SR5

1 Answer

I have a 1987 toyota pickup 22r carburetor i replaced the head gasket 2000 miles ago and now it blew again i had the head milled and new head bolts and i used a felpro head gasket what do i do now?


The 22R engine is one of the best engines Toyota built.

With the head off, you should have had the head gasket surface machined and the head checked pressure checked for cracks. It seems you did so.

I can only assume, you MAY have put the bolts back in without bowing out the cylinder block bolt holes before installing the bolts. These bolt holes fill with oil and antifreeze when you remove the head.

Doesn't matter how careful you are, the bolt holes always fill with fluid.

If so, the bolt torque would be reached before full clamping of the cylinder head. Worst of all, the block could have been cracked by the hydraulic pressure in the bolt hole as you tightened the bolt.

Jan 25, 2011 | 1987 Toyota Pickup

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

2 Answers

Torque specs for toyota tercel


Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Apr 08, 2009 | 1998 Toyota Tercel

1 Answer

Torque specs for 1998 tercel 1.5L


Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Apr 08, 2009 | 1998 Toyota Tercel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...