Question about 1995 Nissan Pathfinder

1 Answer

1993 pathfinder reverse gear

When I Shift to reverse it works if I don't push the accel pedal. When I push the accel pedal in reverse the transmission just doesn't works, it feels like if it goes to neutral...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 199 Answers

Check transmission fluid

Posted on Jul 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Nissan Pathfinder 4wd starts and runs fine but it will not go into gear to drive or reverse,what is the problem?


How To put a Nissan Into 4 Wheel Drive - YouTube

? 2:09
https://www.youtube.com/watch?v=IirIxH0WIVI
Mar 13, 2011 - Uploaded by suzuki230
Just a quick How To, on putting your Nissan into 4 wheel drive. ... to warn the newbies not to drive on hard surface while in 4WDthis can ... If you're having difficulty engaging the 4wd low gear, you can steer ... Hey man i have a 1991 nissan pathfinder SE im going to install a ... How fast can you go on 4L?.

Nissan Pathfinder Questions - automatic will not go into any ...

www.cargurus.com > Questions > Nissan > Pathfinder

CarGurusautomatic will not go into any gear - was driving and parked. now it wonit go into gear. ... Asked by avips Apr 14, 2010 at 04:02 PM about the 1993 Nissan Pathfinder. Question type: Maintenance & Repair ... 2002 Nissan Pathfinder LE 4WD.

Automatic Transmission May Not Shift Correctly at High ...

repairpal.com > Problems > Toyota > 4Runner
truck periodically will not shift into drive at initial start-up. Will very often shift ... 1990Toyota 4Runner- Automatic Transmission100,000Visitor. I have very similar ...

10 Most Common Transmission Problems



Jan 01, 2016 | Nissan Cars & Trucks

1 Answer

I have a 1987 Mazda B2000 pick up. My shifter will not fit back on my newly re-built transmission. Do any other shifters work with this model as I am unable to locate an original for replacement.


I'm sure you have checked the shifter and shifter spring,,...Shifters can be rebuilt also....Make sure your clutch linkage is properly adjusted...The clutch is non adjustable...They may have got air in the hydraulic lines while removing and installing...This would give you a spongy pedal ...Most shifters in order to put it in reverse you push over and up or over and down......if shifter is loose and wobbly it won't have enough force to push the reverse shift rod....However if shifter is in great shape it sounds like the reverse shift rod could be hanging up and not sliding the shift fork...It could be the rebuilders fault......Reverse gear is the largest gear in the transmission and it is located at the back of TRANS which means it will require more force to put in reverse.......I would take it back to rebuilders shop and tell them something isn't right with going to reverse gear...if you wait too long they will think it is something you may have done by incorrect shifting.....

Feb 06, 2015 | 1987 Mazda B-Series

1 Answer

Why won't my 1998 chrysler cirrus shift into gear?


I'm not familiar with YOUR Chrysler, BUT... my brother' father-in-law had a Buick [about 1998 model] that would NOT shift into any gear UNLESS the brake pedal was FULLY DEPRESSED!!!!!

I could move the shift lever into any of the indicator positions, but the transmission would not engage if my foot was not firmly on the brake pedal while selecting a gear position!

Sep 03, 2014 | 1998 Chrysler Cirrus

1 Answer

My 2001 Pathfinder intermittently won't crank (turn key, radio and AC come on but no engine crank). If I push/pull gear shift, it starts - is there a sensor to make sure its in Park to start that may


Many cars do have a switch on the gear shift to ensure it will not start if not in park, turn on the reverse lights when in reverse, turn on the camera when in reverse, park lights, etc. Here is an article that mentions it a little bit, http://www.fourwheeler.com/how-to/transmission-drivetrain/154-0805-1987-2001-jeep-cherokee-neutral-safety-switch/.

Jul 27, 2014 | 2001 Nissan Pathfinder

2 Answers

I have a 1993 nissan pathfinder automatic transmission and it will not move in first gear.it willl move in all other gears,in drive it wont shift out of second unless i push the overdrive button,what


check ecu fuse.your problem could be vechicle speed sensor also. if you dont see any ecu check engine light fuse either blowed or bulb burned out.but if ecu not working vechicle wont shift correct.

Dec 08, 2012 | 1993 Nissan Pathfinder

1 Answer

1989 pathfinder transmission 3spd w/ overdrive works great when first started, then downshifting starts way early, started after alternater wentbad


Do you mean upshifting starts way early? Going from 2nd to 3rd in other words?
Ireally don't know your transmission,but the alternator problem might've possibly spiked and hurt your shifting solenoids in the ******. don-ohio (:^)

Nov 14, 2011 | 1989 Nissan Pathfinder

1 Answer

1998 Ford Taurus SE, Problem Transmissions wont Shift, Took it to the Shop and they Said it Had to be a Electracal Problem?? But they did not Know what, Some times Works Fine Other Times Check Engine Comes...


TRY THIS I BET IT'S YOUR PROBLEM

Neutral Safety Switch
  • Put the selector in the park position.
  • Loosen the screws on the neutral safety switch.
  • Remove the switch.
  • Reverse the procedures to complete the installation.
Clutch Start Switch
CAUTION
Before replacing the clutch switch or any component connected to the vehicle's control computer, disconnect the negative cable from the battery.
  • After replacing the switch, slowly work the clutch pedal and note any unusual noises or interferences with pedal movement.
  • If the switch is adjustable, make sure the clutch pedal height and push rod (free) play are correct.
  • Then check the release point of the clutch.
  • Begin by engaging the parking brake and installing wheel chocks.
  • Start the engine and allow it to idle.
  • Without depressing the clutch pedal, slowly shift the shift lever into reverse until the gears contact.
  • Gradually depress the clutch pedal and measure the stroke distance from the point the gear noise stops (this is the release point) up to the full stroke end position.
  • If the distance is not within specifications, check the pedal height, push rod play, and pedal free play.
  • If the distance is correct, check the clearance between the switch and the pedal assembly when the clutch is fully depressed.
f_mt_tps9.26.jpg Clutch switch to pedal assembly clearance. Courtesy of Toyota Motor Company.
  • Loosen the switch and adjust its position to provide for the specified clearance.

May 22, 2010 | 1998 Ford Taurus

4 Answers

MY switch to put my 2001 nissan pathfinder sticks


I don't believe the previous post/answer was correct. I have had this problem as well on an 01' Pathfinder. It's NOT the transmission. There are two elements to your shifter not being able to unlock/move. The first is a Shift Lock Relay which is located next to the brake pedal arm under the dash. When you step on the brake to shift it out of park, the arm hits the relay and this relay sends a signal to the next component, which is called a Shift Lock Solenoid. This solenoid is located next to the shifter itself under the console cover. When you step on the brake you should hear a "click". This click is the lock solenoid on the shifter releasing, at which point you can push in the button on the shifter and move it to reverse or drive. If you do not hear the click, you can't push in the button and move the shifter. Listen for the click. If you do not hear it, have somone check if your brake lights come on when you step on the brake pedal. If they do not come on, it's a faulty relay which can easily be replaced. It's not sending the signal to the lock solenoid telling it the brake pedal is being depressed. Look under the dash right next to the brake pedal arm and you will see it. If your brake lights come on, but no click is heard, try adjusting the relay to be closer to the pedal arm. If that does not work, it's most likely the lock solenoid next to the shifter under the console. (This was my issue). I have a Chilton's repair manual picked up from the local auto parts shop that does have this solenoid shown and how to remove and test it. You have to remove the console to get at it which is easy, but a pain in the rear. The manual will walk you through this as well. Basic hand tools are all that is needed. A new shift lock solenoid can be purchased from your local Nissan dealer. The parts stores around here (Minnesota) such as O'Reilley's, Autozone, Napa, etc. do not carry them. Mine was $125 from Nissan. There are two different solenoids depending on your VIN number. One was used on early 2001 models and a different one on later 2001 models. Write down your VIN number and bring it with you to the dealer. I had to do this since the part is not stocked and had to be ordered. They couldn't just compare the old part to the new one from a shelf. It took two days to get the new solenoid. I put the new one in place, snapped the wire connector back on and life was good again. No more listening to my wife gripe about it taking 10 minutes to get it in gear and out of the driveway. Hope this helps Scott.

Oct 23, 2009 | 2001 Nissan Pathfinder

2 Answers

Reverse just quit on '95 Pathfinder


If it is an automatic transmission it probably needs transmission fluid. If a standard shift check and adjust shift linkage.

Jul 08, 2009 | 1995 Nissan Pathfinder

1 Answer

1993 Saturn SL2 will not shift into highway gear


Saturn says and I quote

there transmission fluid is not to be changed after the first change at 6000 miles.

Now I say it should be changed at every 30000 miles. If changing out the fluid doesn't work then you need to go to a transmission repair shop.

Feb 19, 2009 | 1993 Saturn SL2

Not finding what you are looking for?
1995 Nissan Pathfinder Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...