Question about Cars & Trucks

1 Answer

Replacing front wheel stud on 2005 grand am? - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 9,587 Answers

If it's broken flush, use a hammer and punch to push it out the back. It will move with persuasion . When installing the new one, use the lug nut and a larger nut that will slip over the threads without touching them to pull the new stud back into place.

Posted on Aug 13, 2017

Testimonial: "Thank you Lawrence, I should have been a bit more clear in my question. is there a "clearance spot" for the stud to pass through without removing the whold hub?"

  • Lawrence Oravetz Aug 16, 2017

    That shouldn't be a problem. There should be enough clearance. I have never had to remove the hub in order to replace a broken stud.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CRTN
  • 716 Answers

SOURCE: Do I need to replace wheel studs or entire hub for front 1995 960

You Can Replace The Wheel Studs Call Napa And Find Out How Much They Are. Dont Go Dealer Cause They Are $20 A Piece And At Napa Like $4 Also You Can Try Autozone Or Kraigen But They Never Have The Ones I Need. Its Also Very Easy To Do Yourself If You Can Change The Brakes You Can Do This. You Can Have Them Pressed In At Any Tire Shop Usually $5.
Happy Fixing
Sincerely,
Michael Scott

Posted on Jan 12, 2009

cadman000
  • 607 Answers

SOURCE: I am trying to replace

With adrift punch. bang out broken stud from huB. Will take some severe hammerering, so using a heavy short handle sledge is advised. Now place the new stud into the hub hole. Put the lug nut on , TIGHTEN ( preferablly with an air impact gun ) as tight as you can till the stud bottoms out. Then you're done. Hope this helps

Posted on May 09, 2009

  • 22 Answers

SOURCE: 2003 hyundai elantra gls front wheel stud broke

grab a large punch and hammer and knock out the old broken one. Push the new one in and re tighten. This will pull it into place and because it has splines it should not spin while doing so.

Posted on Jun 10, 2009

Testimonial: "excellent advice"

  • 112 Answers

SOURCE: broken stud on left front wheel

Remove: wheel, brake caliper & rotor. Drive out the remaining stub with a hammer and punch. Insert a new stud and pull it into place by tightening the lug nut. Before running out of threads, remove the nut, insert a stack of washers or a large nut which slips over the threads without contacting them, tighten the lug nut to seat the stud.

Posted on Jul 12, 2009

  • 39 Answers

SOURCE: Front wheel stud replacement for a 2006 Hyundai Sonata GL.

grind a flat spot on the round head of the new stud this should give enough clearance to install it. don't pull the hub this will damage the bearing.

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front rotor will not tighten down


Nothing. The rotor is held on by being sandwiched between the wheel and the hub. You slide it (the brake rotor) over the studs and mount the caliper over the rotor. Then fasten the caliper to its attach points. When you mount the tire/wheel and tighten the lugnuts this prevents the rotor from coming off. Get yourself to the local library, and checkout the automotive repair manual for your make and model of car. Run through the steps for removing/replacing the brake rotor. Verify you did all the steps correctly!! Good luck.

Nov 08, 2013 | 2005 Pontiac Grand Prix

1 Answer

I can replace the front wheel studs on my 2005 honda accord


yes Is real easy remove tire,brake caliper and the brake disk now put a old nut on the bad stud for remove check is only on 1 location where is space for remove all stud 1 by 1 use a medium hammerand hit to remove the studs or use special clamp to remove and install.

Aug 30, 2012 | 2005 Honda Accord

1 Answer

Broken front wheel stud 2003 grand caravan


jack up vehicle, remove tire. knock out old stud with a hammer and punch. put new stud in from back if need be. to draw it up tight.use a lug nut with something under it so when you tighten the nut it brings the stud into position. remove the nut you put on. and replace the tire. good-day! if the brakes and rotor are in the way. you will have to remove them to replace the wheel stud.

Mar 28, 2012 | 2000 Dodge Caravan

1 Answer

I broke 3 stud on the front can they be replaced


Hi...yes they can...but not an easy task unless you're very mechanical and have the know how. Here is a link showing new replacement studs for your vehicle:

http://www.autozone.com/autozone/parts/2005-Scion-xB/Wheel-Stud/_/N-jmqz9Z6o25b?filterByKeyWord=wheel+studs&fromString=search

If I can help further...post a comment,

over4dy

Sep 18, 2011 | 2005 Scion xB

1 Answer

Broken wheel stud


Unless you hit a curb or something you have bumper to bumper warranty for 3yrs.36 k miles.If not then you can remove the wheel and brake caliper and rotor.Then pound the stud out with a hammer and reinstall the new one.Use a socket or some type of spacer and put on new stud once you have put the stud through the axle.Install the new nut on and start tightening til the stud is seated on the axle.Reinstall the wheel and torque to specs.Depending on type of wheel could be 80-100 ft.lbs.Hope this helps.Good luck.

Dec 23, 2009 | 2002 Pontiac Grand Am

1 Answer

How to replace front broken wheel stud on a '02 jeep grand limited 4x4...steps involve to replace the bolt with a new one? thanks!


Remove wheel, brake caliper and rotor. Give the broken lug a good shot with a decent weight hammer and drive it out of the hub flange. Put new stud into hole, place a stack of washers on it and place the lug nut on backwards (flat side in)
Use oil on the threads to prevent binding, tighten lug 'till stud is seated, replace everything you removed.

Aug 11, 2009 | 2002 Jeep Grand Cherokee

1 Answer

I was trying to remove my front passenger tire & broke wheel stud


You just have to hammer it out. and rotate the hub so you can get it out. then put the new 1 on and tighten a lug on it till it's locked in

Jun 05, 2009 | 2005 Pontiac Grand Am

2 Answers

Broken wheel studs on 1996 grand am se- passenger front


usually they are an assembly but when i get crazy and damage studs i raise and support both front wheels so i can turn them and slowly move the hub where you can fit teh stud in and use an open lugnut to tighten down it will pull the stud in (i use an air compressor for this)

Apr 28, 2009 | 1996 Pontiac Grand Am

1 Answer

Front wheel stud on 2005 honda civic


U must remove the hub assembly to replace the stud.

Mar 24, 2009 | 2005 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...