Question about Cars & Trucks

1 Answer

Why would vehicles with same motor and tyranny have differ torque converters

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 303 Answers

When using an automatic transmission, it's the torque converter's job to transmit and multiply the engine torque, and deliver it to the transmission. If you cut open a race torque converter, inside you will find: the turbine, stator with sprag, and impeller pump. The converter's turbine is attached to the drivetrain via the input shaft of the transmission. When the turbine moves, the car moves.Depend's on what model the car it was you took the motor and tranny out of !!! (More Info)

We Are Here To Help!!

Posted on Aug 13, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 pontiac montana and am trying to figure out how to change the starter.


STARTER REPLACEMENT (ENGINE ELECTRICAL) Document ID# 688149 Starter Replacement

Removal Procedure

Important: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.
  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.
  2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.


  3. Remove the starter motor BAT terminal nut and electrical leads.
  4. Remove the starter motor S terminal nut and electrical lead.
  5. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  6. Remove the starter motor bolts.
  7. Remove the starter motor.

Installation Procedure



  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in Cautions and Notices.
  3. Install the starter motor bolts.Tighten:
    Tighten the starter motor bolts to 47 [n-m] (35 lb ft).
  4. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E.


  5. Install the starter motor S terminal electrical lead and nut. Tighten:
    Tighten the starter motor solenoid S terminal nut to 3 [n-m] (27 lb in).
  6. Install the starter motor BAT terminal electrical leads and nut. Tighten:
    Tighten the starter motor solenoid BAT terminal nut to 10 [n-m] (89 lb in).
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.

Aug 05, 2016 | 2001 Pontiac Montana

1 Answer

Trying to put a front tranny seal in


I hope you have some help and a floor jack. tyranny jack would be better. pull the tyranny, pull the torque converter and pull the seal. be careful and don't get hurt.

Apr 03, 2014 | 1994 Chevrolet S-10 Blazer

1 Answer

Remove transmission on a 1998 Dodge Caravan with a siezed motor


I have done that job casually,I can tell you that it is safer to get down together

Be sure to remove the torque converter screws before separating the engine from transmission , May cause damage to the bushing inside the transmission oil pump

mecanica03@hotmail.com , @mecanicasesoria

May 25, 2017 | 1998 Dodge Caravan

1 Answer

We just rebuilt the motor in a 2000 ford taurus flex fuel vehicle. The car sounds great and the motor is running fine. The transmission that was working fine before won't go into gear now and makes a...


did you hook up the flywheel to the torque converter? the clicking and grinding noise could be the trans is in park and the flywheel is going around, or the torque converter is bound up and not properly in the pump of the trans, and the clicking and grinding could be the parking pawl trying to stop and lock the trans.(this is what stops the car from rolling) I think its a torque converter alignment problem.

Jan 16, 2011 | 2000 Ford Taurus

1 Answer

How do i change the starter on a 1997 buick park avenue?


Removal & Installation To Remove:
Starter 9306xg03.gif

  1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
  2. Disconnect the battery negative cable
  3. Raise and support the vehicle
  4. Remove the transmission cooler line clip if necessary
  5. Remove the torque converter cover
  6. Disconnect the battery positive cable from the starter
  7. Disconnect the wire from the starter solenoid S terminal
  8. Remove the 2 starter motor mounting bolts and the starter motor
To Install:
  1. Install the starter motor
    • Torque the mounting bolts to 32 ft-lbs (43 Nm)
  2. Connect the battery positive cable to the starter
    • Torque nut to 12 ft-lbs (16 Nm) (1997-2000);
    • Torque nut to 89 in-lbs (10 Nm) (2001-2005)
  3. Connect the starter motor S terminal wire
    • Torque nut to 22 in-lbs (2.5 Nm)
  4. Install the torque converter cover
    • Torque the bolts to 115 in-lbs (13 Nm)
  5. Attach the transmission cooler line clip
  6. Lower the vehicle
  7. Reconnect the negative battery cable
prev.gif next.gif

Dec 09, 2010 | Buick Park Avenue Cars & Trucks

2 Answers

Where is the starter


Radiator side of engine block lower

Oct 26, 2010 | 1998 Pontiac Grand Prix

2 Answers

How to remove starter


Removal & Installation - Starter
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle assembly
    Electrical connections Torque converter cover Starter
To install:
  1. Install or connect the following:
    Starter. Torque the bolts to 35 ft. lbs. (47 Nm). Torque converter cover Solenoid -BAT- terminal. Torque the nut to 89 inch lbs. (10 Nm). Solenoid -S- terminal. Torque the nut to 27 inch lbs. (3 Nm). Radiator air baffle assembly Negative battery cable
  2. Perform a charging system test and verify the starter is operating properly
8e0154d.jpg

Fig. Showing the starter motor location and electrical connections
  1. Before servicing the vehicle.
  2. Remove or disconnect the following:
    Negative battery cable Radiator air baffle, for clearance if necessary Flywheel inspection cover bolts Flywheel inspection cover Electrical connections from the starter motor Starter motor mounting bolts Starter motor
To install:
  1. Install or connect the following:
    NOTE Before installing the starter motor to the engine, tighten the nut next to the cap on the solenoid BAT terminal. If this terminal is not tight in the solenoid cap, the cap may be damaged during installation of electrical connections and cause the starter motor to fail later.

    Starter motor Starter motor mounting bolts and tighten the bolts to 30 ft. lbs. (40 Nm) Electrical connection to the battery terminal on the solenoid and tighten the battery terminal nut to 13 ft. lbs. (17 Nm) Electrical connections to the S terminal on the solenoid and tighten solenoid S terminal nut to 27 inch lbs. (3 Nm) Flywheel inspection cover Flywheel inspection cover bolts Radiator air baffle, if removed
  2. Connect the negative battery cable

Hope helps, remember rated this.

Aug 12, 2010 | 2001 Pontiac Montana

1 Answer

I have 1997 Plymouth Voyageur van 11800K Since last couple of months this van won't go into drive or reverse etc.. Then when it finally goes into drive and I drive a block or two then all of a sudden, it's...


It sounds luck the pump in the trans is sucking air instead of oil. Have trans serviced, oil and filter change. All those additives will only hasten its total failure.
Serviceing will dump all of it. and the proper oil will be put into it. Tell them to flush the torque converter also. Good Luck_Ned_

Nov 02, 2009 | 1998 Plymouth Voyager

1 Answer

Replace an alternator on a 2005 chevy venture (instructions)


REMOVAL PROCEDURE

IMPORTANT: This vehicle uses the PG260 F1 starter motor. The starter motor is serviced only as a complete unit.

  1. Disconnect the battery ground (negative) cable from the battery.
  2. Raise and suitably support the vehicle. Refer to Vehicle Lifting.
  3. Remove radiator air baffle assembly.
  4. Remove the starter motor BAT terminal nut and electrical leads.
  5. Remove the starter motor S terminal nut and electrical lead.
  6. Remove the torque converter co
  7. Remove the starter motor bolts.
  8. Remove the starter motor.
INSTALLATION PROCEDURE
  1. Install the starter motor.
  2. Install the starter motor bolts. Tighten the starter motor bolts to 47 N.m (35 lb ft)
  3. Install the torque converter cover.
  4. Install the starter motor S terminal electrical lead and nut. Tighten the starter motor solenoid S terminal nut to 3 N.m (27 lb in).
  5. Install the starter motor BAT terminal electrical leads and nut. Tighten the starter motor solenoid BAT terminal nut to 10 N.m (89 lb in) .
  6. Install radiator air baffle assembly.
  7. Lower the vehicle.
  8. Install the battery ground (negative) cable to the battery.

Jul 25, 2009 | 2005 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...