Question about Cars & Trucks

Open Question

07 Yukon. Access for urpa sensors. - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ultrasonic rear parking assist URPA doesn't work, what should I look for?


  • Dirty or defective sensors
  • Control board defects
  • Open fuse

Oct 20, 2013 | 2007 Pontiac Montana

2 Answers

Where is the cam shaft location sensor located on a 2005 gmc yukon


camshaft sensor located above crankshaft pulley, the camshaft sensor mounted on the front timing cover above the crankshaft pulley.

Sep 17, 2012 | 2005 GMC Yukon

1 Answer

GMC 07 Serria backup sensor will not work. I had a new bumper installed. At first it beeper all the time. Now it will not come on. The DIC shows park assist off.


#PIT4878: Service Park Assist Message / LEDs Stay On Or Inop - keywords B0968 inoperative lamp led light lit module reverse urpa - (Jun 12, 2009) 999999995.gif Subject: Service Park Assist Message/ LED's Stay On or Inop Models: 2007-2009 Chevrolet Silverado 2007-2009 GMC Sierra With RPO UD7

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern: Some customers my comment of a Service Park Assist Message on the DIC and/or the LED indicators at the right rear pillar staying on or inoperative. This concern could be caused by the wiring harness to the LED indicators being pinched under a ground eyelet at the right rear pillar, as shown below.

2290161.gif
other issues could be the problem such as poor connections at each sensor or damaged sensors. to clear URPA codes,place ignition in run,(engine OFF),shift into reverse and turn key OFF.place shift lever into park and retest operation of URPA. if still inop URPA code(s) need to be retrieved before further diagnosis can be accurately done.

Sep 15, 2011 | 2007 GMC Sierra 1500

1 Answer

2003 yukon xl oil pressure guage is at 80 (top end) When I excellerate the gas pedal the oil pressure guage drops to 0.


Hello: You may have a inaccurate oil pressure sensor, you might try replacing the sensor but you have to remove the intake manifold to access the oil pressure sensor

Jan 21, 2011 | 2005 GMC Yukon

2 Answers

When i turn on the a/c my2001 gmc yukon losses power?


This is normal....the air conditioner compressor takes up to 15 horsepower from your engine, and under certain conditions, can make a noticeable difference.

Jun 01, 2010 | 2001 GMC Yukon

1 Answer

I have an engine code PO332 knock sensor 2 circuit low imput bank 2 what is this problem .the car is a 2001 gmc yukon xl .


The most likely cause of your code is a bad rear knock sensor. You should check the knock sensor wiring harness for corrosion. But if that checks out the sensor will have to be replaced. The knock sensor is under the intake manifold, although it's not too difficult to remove. Both knock sensors should be replaced along with the wiring harness, just because of labor involved in gaining access to the sensors. You could try clearing the code, it may stay off for a long time.

May 23, 2010 | 2001 GMC Yukon XL

2 Answers

Wanting to know how to change knock sensor on 2001 gmc yukon


Knock sensor is located on side of engine block screwed into a block coolant drain, your best access is from underneath the vehicle. Coolant will run out when you unscrew it so be sure the engine is cool. Just unplug the wire unscrew the sensor, screw in the new one and plug the wire back in. Also be sure to top off the radiator if you loose any coolant.

Mar 11, 2010 | 2001 GMC Yukon XL

1 Answer

Locate camshaft position sensor on 07 GMC Yukon XL 1500 5.3l


Front of the engine above the crank pulley slightly to the right of center.

Oct 12, 2009 | 2007 GMC Yukon

1 Answer

07 GMC Yukon liftgate will open, but not close automatically


Check on the Strut Assembies on Each side of the Door. There should be a Safety device on them that will allow you to keep the door up, They could be Catching at the Open Position.

Jan 12, 2009 | GMC Yukon Cars & Trucks

1 Answer

2003 GMC Yukon


You will have to remove the intake manifold to gain access to the knock sensors. There are two sensors in the valley under rubber plugs. The sensor in the rear has a tendency to fill up with water and cause trouble. You have to make a dam with RTV to stop the water from getting in there.

Sep 06, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...