Question about Cars & Trucks

Open Question

Is there a fuse for 2002 trial blazer door locks

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
morse008
  • 1111 Answers

SOURCE: My power locks will not work on my 2002 chevy

well although it {the fuse looks good did you pull the fuse to inspect and ensure the fuse truly is good and not blown ...otherwise the wires between the door jamb have broken from the constant wear from opening and closing the door or the switch is malfunctioning { gone bad} and testing with a test light will help you determine exactly this a test light is about 8or 10 bucks for a cheaper one {{{ but 1st most check the fuses }}} it may save you time and money before you begin tearing into wiring etc...

Posted on Dec 17, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: 95 s10 blazer 4dr power door locks inop, new

1. Locate the red two wired programming connector located near the central locking control module that is located behind LH Lower instrument panel. Drop the panel and you will see the red programming connector that is not connected to anything.
2. Inside the Red programming connector you will see to pins..
Jump two pins with a section of wire.
3. System should now lock and unlock doors to indicate vehicle has entered programming mode.
4. Press any button on keyless remote once. System should now lock and unlock doors indicating the keyless remote has been programmed.
5. Repeat step 4 to program other remote.
6. Remove jumper wire from programming connector to exit programming mode.
7. Test Remote(s)

Posted on Dec 22, 2009

  • 1 Answer

SOURCE: 1999 chevy blazer auto door locks and the rear hat...

Ok, heres the fix, 3 amp fuse marked windows / locks in the underhood fuse box. Changed it out and everything works again. Hope this helps you.

Posted on Jun 20, 2010

jrhinoh
  • 8 Answers

SOURCE: 2002 chevy blazer passenger power window will not power up, dead as a door knob.

if all the windows work but the passenger side then its not a fuse its the power window switch in that door pop the switch out and unplug it then take the switck out of the back door if it is four door and plug it in if it rolls the window up you need a new switch

Posted on Oct 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 chevy Blazer 2 door. Power locks,and liftgate stop working.The locks will engage when I shift to drive and will disengage when placed in park. Where do I start?


Hi,
Plz explain...are the locks supposed to lock/unlock when you put the car in Drive/Park, or not?

Does the lock/unlock SWITCH on the DRIVER'S door work/not work? If applicable, does the PASSENGER's door lock switch work?

Td

Dec 29, 2014 | 2002 Chevrolet Blazer

1 Answer

1991 Chevy Blazer auto door locks stopped working.


Broken wire inside rubber sleeve between door and body, or switch is bad. You might want to check fuses also.

Jan 18, 2013 | 1991 Chevrolet S-10 Blazer

1 Answer

I have a 1997 chevy blazer 4x4 4.3 engine dome lights will not go off even when car is running,when i loced doors with the automatic button light would come on and would only lock passenger door but w


there's a black box under neath the steering wheel behind the panel unplug it it worked for my blazer i had the same problem it took me 2 months to figure it out i changed all the dome light switched and the fuses so i unplugged the black box under the dash below the steering wheel and it works fine now

Nov 18, 2012 | 1997 Chevrolet Blazer

1 Answer

2002 chevy blazer passenger power window will not power up, dead as a door knob.


if all the windows work but the passenger side then its not a fuse its the power window switch in that door pop the switch out and unplug it then take the switck out of the back door if it is four door and plug it in if it rolls the window up you need a new switch

Oct 07, 2012 | 2002 Chevrolet Blazer

1 Answer

98 Chev Blazer. power lock problem. driver's door would not unlock doors, now it will not lock doors. passenger side works fine


you may just have a bad connection under the lock button under switch panel on your drivers door. check electrical plug in at door lock switch by removing that panel from driver door.it may be that you have to replace that door lock switch .thers only one fuse for door locks and if pass side works, it's not blown.

Aug 19, 2010 | 2001 Chevrolet Blazer

1 Answer

My alarm on my 01 blazer is going off unprevoked.


this may sound stupid but change the fuse for the power locks and window mine did this same thing i changed that fuse its all fixed now

Jan 21, 2010 | 1999 Chevrolet Blazer

1 Answer

My power locks will not work on my 2002 chevy Blazer... they just stopped working ? any tips? the fuse on the inside door seems to look good...


well although it {the fuse looks good did you pull the fuse to inspect and ensure the fuse truly is good and not blown ...otherwise the wires between the door jamb have broken from the constant wear from opening and closing the door or the switch is malfunctioning { gone bad} and testing with a test light will help you determine exactly this a test light is about 8or 10 bucks for a cheaper one {{{ but 1st most check the fuses }}} it may save you time and money before you begin tearing into wiring etc...

Dec 17, 2009 | 2002 Chevrolet Blazer

1 Answer

Reprogram keyless entry


It took me a few attempts to program a new keyless remote for my 2002 Chevy Blazer.
Insert key into ignition but don' turn it yet. While holding down the UNLOCK switch on the door, the trick is to cycle the ignition ON OFF ON OFF as quickly as possible then release the UNLOCK switch. If done correctly the door locks will cycle 1x to acknowledge. Then hold both the unlock and lock buttons down on the remote for about 15 seconds. The locks should cycle again to confirm...Hope this helps.

Mar 19, 2009 | 2002 Chevrolet Blazer

2 Answers

Keep blowing out auto door lock fuse


You have a short Somewhere. Check inside the Door where the Harness goes into the Doors. It is the Black Flex duct that looks like a Vacuum hose.

Jan 19, 2009 | 2004 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...