Question about Cars & Trucks

Open Question

Remote setting fobs on the panel I have purchased for some reason will set system but will not unset the system. Any suggestions?

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i know if my wifes car is equipped with a remote start system?


Key FOB is to unlock the doors & set the security system,
nothing to do with a remote start

Feb 05, 2013 | 2008 Saturn Aura XE

2 Answers

2004 Elantra. New door locking bought from the US has instructions and diagrams which don't relate to my car. They show a control unit with a switch and have relevant instructions for programming the...


Welcome to Fixya

Try this procedure:

Access alarm system control module. It is located on the at the facia panel in the center. Once you have found this module, ensure that the memory switch is in the OFF position. Then turn the ignition on. Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module. If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button. Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes.

Thank you for using Fixya!

Aug 21, 2011 | Hyundai Elantra Cars & Trucks

2 Answers

2002 VW Cabrio alarm problem: alarm will not un-set. Door will not lock using the key OR the remote. Hitting "alarm off" button on remote, it unsets, then arms again immediately. With engine...


i have a 2002 vw cabrio and won't start after i took out the battery everbody is telling me that anti-theft is lock mode how do i rest it so i can start my car

Nov 08, 2010 | 2000 Volkswagen Cabrio

1 Answer

I purchased a pre-owned 2003 Toyota Avalon, I did not get a remote entry transmitter with the keys, how do I know if the car came equiped with a remote entry system.


A TOYOTA AVALON MORE THAN LIKLY CAME WITH A KEY FOB BUT ONE WAY TO CHECK WOULD BE AT ATOYOTA DEALERS PARTS DEPT., THEY CAN USE YOUR VIN NUMBER TO SEE IF THE VEHICLE CAME WITH A SET AND EVEN GET THEM REPLACED

Nov 29, 2009 | Toyota Avalon Cars & Trucks

3 Answers

2001 Santa Fe Key fob Programming


change the batteries then start the car and close it and press the key it should work

Nov 15, 2009 | 2005 Hyundai Santa Fe

1 Answer

WHEN I SET MY ALARM IN MY 1997 TOWN and COUNTRY IT WONT UNSET AND I CANT START MY CAR, I TRIED THE LOCK THEN UNLOCK WITH THE KEY BUT NO LUCK SHUTS RIGHT OFF, CAN I OVERIDE OR MANUALLEY RESET MYSELF


TRY PUTTING NEW BATTERIES IN YOU FOB[REMOTE].IF THAT DOES'NT WORK YOU WILL HAVE TO GET A NEW OR USE YOUR SPARE IF YOU HAVE ONE,IT CAN'T BE OVERRODE.

Oct 12, 2009 | 1997 Chrysler Town & Country

1 Answer

Key fob not working


Most of these key fobs have a number (FCC#) on the back, or inside the casing. You could go to the dealership and have them charge you a ton of money, or you can by them on ebay and set the switches on the circuit board to match your remote. Just make sure when you buy it the it matches your remote exactly.

Jul 07, 2009 | 2003 Hyundai Accent

1 Answer

2004 Hyundai Santa Fe Reprogramming Remote Entry Fob


Remote control added or replaced.
How
Access alarm system control module located under driver's side lower fascia behind fuse box, should see it without removing any parts. Fig. 2 . Set memory switch to SET position using a very small screwdriver. Press remote control lock or unlock button. Set memory switch to OFF position. Fob won't move locks until you put it in the off position. Confirm synchronization has been successful by locking and unlocking vehicleicon1.png. Repeat procedure for second remote control or in my case I did them at the same time and they both work fine. Synchronization can also be carried out using diagnostic equipment.
NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

Mar 18, 2009 | 2004 Hyundai Santa Fe

3 Answers

How do I program S Type Jaguar key fob Year 2000 Jag ?


Seperate key fobs only can be programmed in the following way.

Turn ignition on/off 8 x times (allow all functions to stabilise) after the 9th on - press a button on both remote fobs. then turn ign. off. use good remote to lock and then try new remote to unlock/lock. sometimes it works first time - sometimes you have to repeat actions. good luck.

Dec 28, 2008 | 2000 Jaguar S-Type

3 Answers

Remote start and door locks will only work from 10 feet or less


i had the same problem... go through the menu until you see reprogram remote. hit the check mark button and hold the lock and unlock button until the horn honks. key has to be on car not running though. You will eventually have to do it again but for some reason it will work for a while.

Dec 04, 2008 | 2006 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...