Question about Honda Cars & Trucks

Open Question

Honda 1994 ballade 1500 cc left rear window regulator removal?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 133 Answers

SOURCE: Rear window regulator line broken

Hi lec the rear glass has a white plastic clip holding the glass to the regulator. try from  the door side, pushing the center plastic pin out toward you then the glass will lift out   D

Posted on Jan 16, 2009

MrScary66613
  • 1990 Answers

SOURCE: 2002 buick lesabre driver side regulator motor removal

You will need to Drill out the Rivets that Hold them Right Now and Use Screws to Reinstall.

Posted on Jan 22, 2009

godspeed808
  • 125 Answers

SOURCE: 1994 Honda Accord LX Rear Window

first if you want to attempt to repair of locate problem purchase repair manual ex:haynes or chiltons then get a multi meter with dc volts settings and impedance settings and a light tester then follow troubleshooting section and electrical system section this isnt the easiest find or repair it can be very fraustrating but Ill do my best:
first locate relays in electrical system section of repair manual test to see when switch is engaged either up or down that there is power coming from relay use schematic in electrical section to determine colors if there is move on
then remove power windows switch using multitester or light tester to see if theres power coming into and from switch in up or down position use electrical schematic in book to determine appropriate color wires
if no power coming to switch you have a wiring problem from relay to switch and the hunt begins looking for damaged wire or ground
then if there is power to and from switch move to regulator and make sure theres power coming in to it when switch is engaged if so your regulator is knackerd replace it if not find damage wire ground or break
if regulator is working and window is off track repair it using either winshield and window sealant/ adhesive or new clips and anchors
for parts see either dealer or these guys most of these parts arent readily available from regualr parts stores but you may get lucky
www.ebay.com
www.godspeedmotorsportsonline.com
peach street auto 18003652341

Posted on Feb 06, 2009

  • 59 Answers

SOURCE: rear window regulator s-type jaguar

Likely will have to replace the regulator that rolls the window up and down

Posted on Feb 23, 2009

  • 33 Answers

SOURCE: how do you remove the glass from the rear side window regulator

Remove the door panel

  1. Remove the side impact bolster.
    e0001157.jpg
  1. Detach the door speaker (if equipped).
    e0003862.jpg
  1. Disconnect the speaker electrical connector and remove the door speaker (if equipped).
    e0003863.jpg
  1. Detach the door latch release handle.
    e0001156.jpg
  1. ani_caut.gif CAUTION: Do not touch the adhesive surface as re-bonding will be impaired.
    Detach the watershield.
    • Using a suitable plastic knife (disposable cutlery), cut through the Butyl strip to enable the watershield to be peeled back.
    e0001158.jpg
  1. Remove the door glass top run retainer.
    e0001160.jpg
Vehicles with manual windows
  1. Install the window regulator handle.
Vehicles with power windows
  1. Connect the door glass operating switch electrical connector.
    e0001851.jpg
All Vehicles
  1. Align the regulator clamp with the access hole (power window shown).
    e0001853.jpg

  1. NOTE: Position the regulator operating cable to one side when drilling the retaining pin, in order to prevent damage.
    Detach the door glass from the regulator clamp.
    1. Using a suitable electric hand drill and a drill bit 8 mm, remove the retaining pin.
    1. Push out the retaining sleeve.
    1. Remove the door glass from the regulator clamp.
    • Discard the retaining sleeve.
    e0001854.jpg
  1. Support the glass, lower the glass and regulator to the lowest position.
  1. Position the lower part of the door glass top run outside the door.
    e0001161.jpg
  1. NOTE: To aid removal of the door glass, stand on the inner side of the door. Make sure the glass is removed from the inside of the door.
    Remove the window glass.
    e0001163.jpg
Installation
All vehicles
  1. ani_caut.gif CAUTION: Make sure vise jaw protectors are used.
    NOTE: Make sure that the retaining sleeve is central in the door glass.
    Attach a new retaining sleeve and retaining pin to the door glass.
    1. Position the retaining sleeve in the door glass.
    1. Using a suitable vise, press the retaining pin into the retaining sleeve.
    e54462.jpg
  1. Install the window glass in the door.
    e0004709.jpg
  1. Attach the door glass to the regulator clamp.
    • Push the door glass firmly down to engage the retaining pin and retaining sleeve into the regulator clamp.
    e54463.jpg
  1. Position the lower part of the door glass top run on the inside of the door.
    e0004707.jpg
  1. Close the window.
  1. Install the door glass top run retainer.
    e0001160.jpg
  1. Attach the watershield.
    e0004705.jpg
  1. Attach the door latch release handle.
    e0004704.jpg
  1. Connect the door speaker electrical connector (if equipped).
    e0003863.jpg
  1. Install the door speaker (if equipped).
    e0003862.jpg
  1. Install the side impact bolster.
    e0004703.jpg
Vehicles with manual windows
  1. Remove the window regulator handle.
Vehicles with power windows
  1. Disconnect the door glass operating switch electrical connector.
All vehicles
  1. Install the door trim panel

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find part number for window regulator clip for rear left Window


Should be a 5 minute task at your nearest dealer. The clips will be genuine part only. Take your VIN number in with you.

Feb 23, 2015 | 2006 Peugeot 206 1.4

Tip

How To Install Replace Rear Power Window Regulator Honda CR-V 02-06 1AAuto.com


How To Install Replace Rear Power Window Regulator Honda CR-V 02-06 1AAuto.com

on May 18, 2012 | 2002 Honda CR-V

Tip

How To Fix Broken Rear Power Window Regulator Honda CR-V 2002-06 1AAuto.com


How To Fix Broken Rear Power Window Regulator Honda CR-V 2002-06 1AAuto.com

on May 10, 2012 | 2005 Honda CR-V

1 Answer

Honda ballade 150i camshaft pulley removal


1980 Ballade? to 1986, a real old car.... is it? really?
alldata.com (not sure if they go back that far...)
or
the real Honda FSM (used off fleabay?)
lots of steps, nobody will post them all...

id bet it matches one of these. RTM your self.
http://hondatech.info/downloads/Auto/Manuals/Civic/

Nov 13, 2013 | Honda Cars & Trucks

1 Answer

How do i set timing belt tension on 1994 ballade 160i sohc


ballade? honda ?
what country
what engine
1.3L EJ I4 (1st gen)
1.5L EM I4 (1st gen)
1.3L EV I4 (2nd gen)
1.5L EW I4 (2nd gen)

: D15B3 - 69kW
D16A7 - 86kW
D16A9 - 96kW
B18B3 - 97kW

lots of engines, to fix engines, you MUST know what you have , or its impossible to do anything, not even buy parts.

The FSM covers this.

Aug 05, 2013 | Honda Cars & Trucks

1 Answer

I want to change the rear brake pads on my Honda Ballade Luxline 1994, 1500. How do I "push back" the cylinder (piston) that applies pressure to the pads? This needs to be done in order to fit the n


you need to get what is called a C clamp this applies pressure to the piston, but before using that, take one of the old brake pads and use it along with the c clamp that should work

Feb 20, 2013 | Cars & Trucks

1 Answer

How to remove and install the driver side window (just the glass) on a 94 honda prelude


Hi!!
Here is how:
REMOVAL & INSTALLATION
See Figures 1, 2, 3, 4, 5 and 6
  1. Remove the door pad and inner moisture barrier.
  2. If working on the rear window of a sedan, remove the two upper screws securing the center channel. Remove the two lower bolts (in the door) securing the channel and remove it. On some cars, the two screws are concealed below the weatherstrip.
  3. For sedan rear doors, remove the quarter glass. The entire glass and rubber seal may be removed as an assembly from the door.
  4. Lower the door glass until the glass mounting bolts are accessible. One will be easily seen in the large access hole in the door; the other will appear in the smaller, round access hole. Remove the bolts.
  5. Stand next to the inside of the door. Tilt the door glass and remove it through the slot.
  6. On front doors, remove the bolts securing the front run channel, then remove the channel.
  7. Remove the regulator mounting bolts and remove the regulator. On later models, there are additional roller guide bolts to be removed. Mark the roller guide mounting bolts to ease window alignment later.
  8. For power windows, remove the motor from the regulator if desired.
CAUTION The regulator gear will move suddenly when the motor is removed due to action of the large spring. Keep hands well clear.
TO INSTALL, REVERSE DIRECTIONS
FIG 1 1kbron_122.gif

FIG 2 1kbron_123.gif
FIG 3 1kbron_124.gif

FIG 4 1kbron_125.gif

FIG 5 1kbron_126.gif

FIG 6 1kbron_127.gif

Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Feb 16, 2011 | 1994 Honda Prelude

1 Answer

Replace the left rear electric window cable.


you cant fix cable, you need the Window Regulator

Jul 23, 2010 | 1994 Isuzu Trooper

1 Answer

How do you replace window regulator on 1994 honda


hello there:
to replace the window regulator you will need too look for screws around the sides and bottom of the door panel then you will need to remove the door handle backing plate and the door handle where you grab too close it you see no screws there will be a round cap you will need to take out to see the screw head remove the screws and lightly pull the door panel out there will be body clips that will come out of the door then slide door panel up and pull off this will give you access to the regulator remove the bolts on the regulator and remove install in reverse hope this help you out please leave a review thanks sincerely D.Jones

Jun 03, 2010 | 1994 Honda Passport

1 Answer

Where is the transmission dipstick loacated on a honda ballade 180E auto,1994 model


Most of hondas dipsticks are on the passenger side of the car near the front of the car usually a really short stick.way down low.

Jul 31, 2009 | 1994 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...