Question about Toyota Cars & Trucks

Open Question

Buildup of pressure in the hydraulic clutch system Toyota dyna truck

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fastboyz
  • 674 Answers

SOURCE: bleeding hydraulic clutch

well you will need some help
make sure the resivor is full and have someone hold the clutch pedal to the floor and crack the bleeder on the slave cyl. and close after the spert of fluid comes out. when the screw is closed have the person in the drivers seat slowly let up and push down 3 times and hold down and bleed one more time. refill your resivor and repete if you dont think the peddal is quite right. just dont run it out of fluid
good luck it realy isnt that hard.
later paul

Posted on Sep 16, 2008

martin538
  • 117 Answers

SOURCE: Hydraulic Clutch Problem in an 82 Toyota Pickup

If you are leaking fluid from the clutch master cylinder then you have air in the system. You could try and bleed the air out of the clutch slave cylinder to get the gears but it would not last. The only way is to replace the defective master cylinder, replace all of the fluid and bleed out the air through the slave cylinder.

Posted on Apr 07, 2009

  • 1861 Answers

SOURCE: I have a 91 Toyota 4X4 truck. the clutch is

There is a small "master cylinder", forthe clutch, located on the driver side of the engine compartment, below the master cylinder.

Posted on May 06, 2009

wilsodfarm
  • 986 Answers

SOURCE: hydraulic clutch 1995 chevy 1500 truck

I know you dont want to hear this but it sounds like the clutch plate is in backwards.

Posted on Oct 19, 2009

  • 6982 Answers

SOURCE: new clutch not working properly really could use some help

My best guess on this, assuming that the clutch master is working and it has no air remaining in the system is that you either have the wrong throwout bearing in there or that it is installed incorrectly. Also, rare but can happen is that if the pressure plate assembly is a rebuilt one, the face has been cut too far and clearances are off.
Obviously, check everything external before taking it apart again, but that's where I think you will need to go.

Posted on Nov 18, 2009

Testimonial: "thanks did have some issues installing throw out bearing so maybe that is my problem"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 toyota celica clutch is there an adjustment or is it hydraulic?it also smells like burning clutch?


its a hydraulic clutch. the burning smell could be a sign that the fluid in the master cylinder is low and there isn't enough pressure being applied to the flywheel, causing the clutch to slip. if the clutch disengages at near the end of the pedals "throw", as you disengage the pedal, than its a sign your clutch plate needs to be replaced. but to me it just sounds like a hydraulic pressure issue.

Nov 15, 2016 | 2002 Toyota Celica

1 Answer

Why is the clutch not engaging>


Low fluid in hydraulic system,bad slave or clutch master cylinder,bad pressure plate or clutch disc or a stuck throw out bearing are the most probable causes.

Jul 03, 2015 | 2007 Toyota Tacoma

1 Answer

Cant find the clutch reservoir on my audi a4 1.8 eastate r reg..


The Clutch Master Cylinder is located on the firewall inside the engine bay, and usually next to the brake master cylinder as the brake and clutch pedals are usually very close to one another. The Clutch Master Cylinder is responsible for transferring the clutch pedal pressure hydraulically to the slave cylinder to release the clutch. You can tell when your clutch master cylinder is dying or needs repair when you depress your clutch pedal and it slowly sinks to the floor and does not return. Since the entire system is a hydraulic one, the master cylinder also has a reservoir that holds the fluid used in the clutch hydraulic system. If you decide to change the clutch master cylinder it is a good idea to also get a clutch slave cylinder at the same time, as both units typically fail around the same time. When replacing your master or slave cylinder, its always a good idea to flush your entire system to prevent water buildup or air pockets from being present when you are driving. Also always keep an eye on the fluid in your reservoir, dirty fluid may mean that the internal seals are allowing dirt and contaminants into your master cylinder.

Oct 11, 2011 | 1997 Audi A4

1 Answer

TRUCLKINGCLUTCH IS SLIPPING IS THERE SOMEWHERE TO ADJUST OR ADD FLUID


The clutch is hydraulic, so there will be a bleeder screw on the line, but bleeding it will not have much impact if any. The reason is that the hydraulic system keeps pressure on the clutch, so you will be better off by replacing the clutch.

Mar 29, 2011 | 2004 Toyota Celica

1 Answer

Clutch goes to the floor when pressed


This sounds like you have no pressure in the clutch hydraulics. If the clutch master cylinder and slave cylinder are the original ones, they probably need to be replaced. Bleeding the hydraulic system may help for a short while, but if these are the original parts, they need to be replaced.

Dec 04, 2010 | 1992 Toyota Pickup

2 Answers

I have an old 1989 Toyota dyna with 14b motor 5 speed. I wish to know if the hydraulic clutch is adjustable and if so how, as mine is slipping and hard to change down gears


hi, no im afraid with the hydraulic clutch their is no adjustment its going to be a case of buying a clutch kit and change the clutch.

If it was cable tight then some are adjustable and some are not but even the ones that are not adjustable you can get round this and adjust them slightly but with your type of clutch their is nothing at all you can do.

Sorry i couldnt give you any good news or an easy fix but its going to be a case of changing parts to solve your problem.

Let me know how you get on or if you need further assistance ok

Jan 14, 2010 | Toyota Cargo Cars & Trucks

2 Answers

My clutch is slipping on my 1993 toyota truck. Are there adjustments I can make myself. I am fairly handy, but not a car repair expert.


Sorry, there are no adjustments on your vehicle., The clutch is activated via hydraulic pressure. The master and slave cylinders are "self-adjusting". If the clutch is slipping, you are going to need to pull the trans and replace the clutch assembly. Changing the hydraulics will not help a slipping clutch at all.

Thanks for choosing FixYa for advice!

Mar 05, 2009 | 1993 Toyota Pickup

2 Answers

Trying to figure out how to adjust the clutch on a 2005 Toyota Corolla style s


You car does not have an "adjustable" clutch. The Corolla uses a hydraulic clutch. The action of the hydraulics eliminates the need for adjustements. If the clutch is slipping, you may need to replace the clutch.

Jan 15, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...