Question about Cars & Trucks

1 Answer

We have 3 outdoor lights connected to one switch. Upon turning switch off, one light remains on. These have been working fine for years. What's going on?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Dedicated:

    Visited the website for 20 consecutive days.

  • Cars & Trucks Master
  • 632 Answers

Is it a dimmer switch? Are the bulbs LEDs? If so, that's your problem

Posted on Aug 12, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: 2000 alero, started up fine,

This is a Direct result of a Bad Alternator. You can Run on what is left in the Battery for a Little while and if it sits for a While the Battery will retain enough Power to Start. You may need a New Battery in Addition.

Posted on Jan 17, 2009

Preeth Tom
  • 129 Answers

SOURCE: I have a nissan pulsar Q 2001 model. When I turn

hi
the problem may be due to the mid spring inside the light switch which cause the turn on ,of the low beam light .its better to replace the light switch near the steering

Posted on Jul 14, 2009

  • 1 Answer

SOURCE: my 1992 corvette Interior light stays on

I am not sure about the 1992 since they have newer dashboard than my 86.

Anyway, I got that same intermittent issue on mine, sometime the battery was drawn in the morning sometime not, very frustrating, until i noticed that the interior light sometime was not going out as it should after 30 seconds when leaving the car in the evening.

I eventually found the timer module after removing the upper dash pad, on the passenger side. The module was just partially unplugged. Put it back in and never got problem anymore (was 6 years ago).

Posted on Aug 24, 2009

  • 27 Answers

SOURCE: high beam indicator remains on all the time, turns

bad earth r dodgi indicator stalk

Posted on Sep 30, 2009

  • 1 Answer

SOURCE: instrument panel lights don't work

please advice, have you solved the problem? I have the same one on my Sebring. Many thanks.

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can i use the light bulbs containing mercury outdoors.?


Hi
I assume you are talking about the energy saver type U tube glass, or spiral glass tube (low pressure mercury vapour)
These work fine outdoors, I have used them for 15 years or so in my outside glass ball light fittings. They soon warm up and vapourize the mercury in the tube, the glass is fine.

Regards Jacko
From down under.

Dec 11, 2016 | Mercury Cars & Trucks

1 Answer

Turn signals don't work!!


Depending on the year make and model, I would suggest having someone check the turn signal switch for power first.

Dec 13, 2012 | Cars & Trucks

1 Answer

I just got a new battery installed for my 1995 GMC Jimmy. Upon installation I discovered that my interior lights were on. I've tried installing another battery, checking the fuses, and checking the switch...


clean and lubricate the switches in the door jamb, and spray with lubricant the door latches-worst case just remove the bulbs until you can spend some time chasing it down, and just because, make certain you don't have the interior lights switched on at the dash (it happens)

Mar 07, 2011 | 1995 GMC Jimmy

1 Answer

I have a nissan pulsar Q 2001 model. When I turn on the lights the park lights come on but on switching to low beam the lights remain in park. High beam works fine. Where would the problem lie?


hi
the problem may be due to the mid spring inside the light switch which cause the turn on ,of the low beam light .its better to replace the light switch near the steering

Jul 14, 2009 | 1990 Nissan Pulsar

1 Answer

1999 VW Beetle outside temp display not working


For general awareness, the outside air temperature sensor is located above the inside mirror.
Try to reset the temperature measurement unit: 1. Switch engine on. 2. Press and hold clock minute (min) and hour (h) buttons simultaneoutly longer than 3 seconds. The display will show new temperature measurement unit. 

Apr 03, 2009 | 2000 Volkswagen Beetle

1 Answer

Iluminite Speaker Instalation 12v DC power


There is 12+ going to the power window switch if you have power windows, you could tap off of that. It's already inside the door, no routing needed. Use continuity test to find ground. Also hook up a seperate switch on the door to turn them on or off.

Oct 17, 2008 | 1998 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...