Question about Cars & Trucks

Open Question

6104 7000 1958 8391 Balance

Need to get balance

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 23 Answers

SOURCE: timing marks 2002 sonata 4 cyl twin cam balance shaft marks

look for marks on the timeing gears there sould be a couple notches. then bring them center to center

Posted on Dec 24, 2008

  • 17130 Answers

SOURCE: balance shaft alighnment

Request that the information is not adequate for such a serious job and so is necessary if your also equipped to handle this work with precision.

Posted on Mar 13, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a Phillips RC604 stero in my hyundia 99 model and the balace has shifted to the rear while cleaning the car iand i cant figure out how to get to balance setting

press the mode button it puts you in touch with the operations loke balance front rear , left right, bass, treble etc and readjust the balance setting

Apr 22, 2017 | Cars & Trucks

1 Answer

Balance shaft repair replace on PT Cruiser

the balance shafts may be out of balance

if guides and chain worn or
some work was done wrong during a timing chain and guide replacement

to get to them ....lots of work
balance shafts are lower part of engine block
number 6 in picture one

front parts of the motor has to be removed
same job as a timing chain and cog kit replacement

I prefer balance shaft elimination option myself
balance shaft elimination kits are available for that motor


elimination kit


Nov 02, 2016 | Cars & Trucks

1 Answer

Do the 2 balance shafts in the oil pump have to be timed together

92 accord 2.2 rear balance shaft - YouTube

? 2:17
Mar 31, 2012 - Uploaded by Shasta Sweetbottom
I believe this is the correct way to set the rear balance shaft on a 92 2.2 accord. ... 1 time, it has gear inside ...

VW and Audi TDI oil pump failure and balance shaft FAQ ...

? 6:54
Oct 5, 2014 - Uploaded by myturbodieseldotcom ... Does the 2013 Volkswagen ...

2.4L balance shaft on oil pump sprocket - Kia Forum

Nov 24, 2015 | Cars & Trucks

1 Answer

How do you get balance shaft drive sprockets off?

You need to remove the balance shafts first. Be VERY careful or you will end up breaking off the tab that the small hold down bolt goes through. You need to remove this little bolt first of course. I found that using a pry bar on the bottom of the sprocket itself seemed to work best.
Once you have the balance shaft out, clamp it in a vise using wood or something similar so that you do not damage any if the surface that rides on the bearing. Then remove the 15 mm bolt holding the gear (sprocket) on. Re-install the new gear and torque to 37 ft-lbs. The new gear is slotted so it can only go on one way. Do not mix up the intake & exhaust balance shaft gears. Good luck.

Jul 07, 2014 | 2003 Chevrolet Cavalier

1 Answer

Does the balance shaft of the 1998 audi a8 need timed

yes -- It is so designed to be out of balance when the crank is in balance so they cancel each other out and there is no harmonic vibration. To achieve this it is necessary to time it correctly

Jan 20, 2014 | Audi Cars & Trucks

1 Answer

Balancing shafts reaon for them

on many V4 engines you need a balance shaft to make the engine smooth ,a V6 doesnt need them its to do with power balance so a 6 cyl has power all round the rotation of the crank a 4 or 3 cylinder hasnt hence a balance shaft ,some engines achieve this with a heavy flywheel others have a balance shaft inside the engine .So a lighter flywheel can be used for a faster acceleration as less weight to get into motion

Mar 29, 2012 | 1996 Toyota Camry

1 Answer


you should be able to, a 4.3 is a 4.3, chevy motor, bellhousing and mounts are all the same, just might need to do some parts swapping from old engine (intake and electical parts)

May 16, 2009 | 1992 Oldsmobile Bravada

1 Answer

Timing marks 2002 sonata 4 cyl twin cam balance shaft marks

look for marks on the timeing gears there sould be a couple notches. then bring them center to center

Dec 24, 2008 | Hyundai Motor 2002 Sonata

1 Answer

2000 radio balance problem

need to clean the balance knob with some electrical cleaner

Oct 31, 2008 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides