Question about Mercury Cars & Trucks

1 Answer

Check left headlamp message - replaced bulb and still not working on 2009 mercury milan premier. Suggestions?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 2,656 Answers

Are you getting power and ground to it ?

Posted on Aug 12, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
wireguy212
  • 1627 Answers

SOURCE: 2007 Mercury Milan Premier V6 ac compressor clutch

you may need to top up the coolant,r112,r140or what ever the car is useing. if the car can'nt be topped up then you have a leak that needs to be fixed,usually the drier.

Posted on Oct 14, 2009

  • 1 Answer

SOURCE: Upgrading 2006 Mercury Milan's sound system with MP3 jack.

Even though your current radio has an AUX button the radio is not programmed to utilize it.
There is no 'easy' way to add the '07 Job 2 and later year model's factory Aux input.
You will need to buy an aftermarket solution. Something like this http://pac-audio.com/productDetails.aspx?ProductId=821&CategoryID=24

Posted on Jan 19, 2010

emissionwiz
  • 76109 Answers

SOURCE: What is the process for replacing the headlamp

Replacing headlamp bulbs
Handle a halogen headlamp bulb carefully
and keep out of children’s reach. Grasp the
bulb only by its plastic base and do not touch the
glass. The oil from your hand could cause the bulb
to break the next time the headlamps are
operated.
If the bulb is accidentally touched, it should be
cleaned with rubbing alcohol before being used.
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood. If you are replacing the driver
side headlamp, unclip the electronic module on the
right side of the battery and move it out of the way.
2. Locate the headlamp bulb through the hole in the
upper radiator support assembly.
3. Release clip and
disconnect the
electrical connector
from the bulb.
4. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) about 1/8 turn to
free it from the bulb socket, and slide the ring off
the plastic base. Keep the ring to retain the new
bulb.
5. With out turning, remove the old bulb from the
lamp assembly by gently pulling it straight out of the
lamp assembly.

To install the new bulb:
1. With the flat side of
the bulb’s plastic base
facing upward, insert
the glass end of the
bulb into the lamp
assembly. You may
need to turn the bulb left or right to align the
grooves in the plastic base with the tabs in the lamp
assembly. When the grooves are aligned, push the
bulb into the lamp assembly until the plastic base
contacts the rear of the lamp assembly.
2. Install the bulb retaining ring over the plastic base
until it contacts the rear of the socket by rotating
clockwise until you feel a “stop.”
3. Install the electrical connector into the rear of the
plastic base until it snaps, locking it into position.
4. Turn the headlamps on and make sure they work
properly. If the headlamp was correctly aligned
before you changed the bulb, you should not need to
align it again.

Posted on Mar 15, 2010

  • 5520 Answers

SOURCE: I am getting a lot

Hello, First thing would be the type of gas you are using. Gas with alcohol in it would not get the mileage of Gas without alcohol. If you were getting 25mpg and drop 10% because of 10% Alcohol in your gas, then that accounts for 2.5MPG of the loss. There is some heat value in the Alcohol, but rule of thumb is less gas is less mileage.

You did not indicate if any "Check Engine" lights were on. You can try to get the car scanned, Autozone, Oreillys, and Advance do it free. But some cars will not record a problem that is intermittent, some cars have to reach a plateau of intermittent events to display a "Checklight".

Not all of the scanners are equal and some places will not connect or test a car without the "Checklight" displaying. Have clean oil and Air filter installed, but watch your tire pressure. Most of the time the Oilchange places let air out of the tires. Have tires inflated below the Maximum rating on the tire BEAD, but usually above the pressure on the door label. Automakers want you to enjoy the soft ride, but it costs you money at the pump.

If your Brakes are dragging it will make a difference. The rear wheels are 2 brakes in one. The Emergency brakes are harder to inspect. Your car is 5 Years old and if you have not had Brake work done, parts may be rusted and not fully retracted.

These are the basics, I think the basics will go along ways into restoring your mileage. The newer cars have more Electronics which are good for keeping an Engine in Tune. Unless you get a "Checklight" most of the potential problems are those which are not monitored. Like tire pressure, clean filters, and Brakes.

Posted on Mar 23, 2011

  • 130 Answers

SOURCE: Labor cost on o2 sensor mercury Milan 2007 v6

You shouldn't pay more than $40 for the installation of an o2 sensor. It is only a 15 minute job at max. Good Luck!

Posted on May 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 mercury Milan premier-po356-missing # 6 cylinder no voltage to spark plug coil what controls voltage to coil


Unless yours is different from most, there is an ignition module which can fail in several ways, and is a common failed item. Failed wiring to coil also possible.

Apr 29, 2015 | 2008 Mercury Milan Premier

1 Answer

Does both headlamp bulbs go out the same time on the 2010 mercury Milan?


Not normally especially for a late model car. Is it out of warranty? If so I would check the fuses first.

Jan 12, 2015 | 2010 Mercury Milan

1 Answer

I just purchased a Mercury 4 cylinder Milan. It appears that the headlights and high beams are not as bright as they should be. Is this normal or should they be replaced (if at all possible) with a...


There are two option you can relace to a bighter bulb,that has brighter intensity, or if the lens are murkey or dull you can have it polished,most shop do headlamp polishing.its is a do it youself kit that will be required you to use a drill,or a shop can do it,if they dont have the kit ,or you can purchase the kit and have your favorite shop do it.

Apr 26, 2011 | 2008 Mercury Milan

1 Answer

When you turn the headlights on everything works but the headlights. If you hold the dimmer switch in the brights will come on. When you let it go the lights go out


Have you tried to change the headlights?

REMOVAL & INSTALLATION Sealed Beam NOTE: If vehicle is equipped with headlamp doors turn the headlight switch ON. Open the hood and locate the power distribution center. This center is located in the front of the left front strut tower. Remove the cover from the center and remove the Headlamp Close Relay. This will prevent the headlamp doors from closing to provide easier servicing. Turn the headlight switch to OFF, then perform this repair.
  1. Remove the headlight bezel.
  2. Unhook the spring from the headlight retaining ring if so equipped.
  3. Unscrew the retaining ring and remove it. NOTE: Do not disturb the two long aiming screws. Conventional and Halogen headlamp sealed beams units are interchangeable in pairs, but it is recommended that they not be mixed together (one halogen and one conventional). It is fine to upgrade from conventional bulbs to halogen, but do not change from halogen bulbs to conventional bulbs, especially if the vehicle came equipped with halogen bulbs.
  4. Unplug the old sealed beam from the engine electrical wiring harness.
  5. Extract the old bulb from its mounting bracket. To install:
  6. Connect the replacement bulb and install it into the receptacle (check operation of headlight before completing repair).
  7. Install the retaining ring and secure it in place with the retaining screws. Connect the spring.
  8. Install the headlight bezel.
Aero Headlamp Aero headlamp systems use replaceable halogen bulbs that are mounted in aerodynamic, molded plastic lens reflector assemblies. NOTE: Lens fogging is a normal condition and does not require service, as moisture will vent from tubes behind the lens on Aero headlamp-type system. EXCEPT PREMIER AND MONACO It may be necessary to remove the entire headlamp assembly if enough access cannot be gained otherwise.
  1. Locate and remove the wire connector behind the headlamp assembly in the engine compartment. It may be necessary to remove certain items in the engine compartment to gain access to the bulb wires.
  2. Rotate the bulb retaining ring counterclockwise 1?4 turn and remove the ring, bulb and bulb holder from the lens assembly. The bulb holder has alignment notches. NOTE: Do not touch the bulb with bare fingers or any possibly oily surface, since reduced bulb life may result! Fig. 1: To remove the light bulb, first unplug the headlight electrical connector, then . . . 86726p13.jpg
    Fig. 2: . . . remove the light bulb socket retaining ring 86726p14.jpg
    Fig. 3: Rotate the light bulb socket 1?4 turn counter-clockwise, then pull it straight out of the lens assembly 86726p15.jpg
    To install:
  3. Wearing gloves or holding the replacement bulb with a cloth rag to keep oil off of the bulb surface, insert the bulb into the rear hole of the headlamp assembly. Make certain that the alignment grooves and tabs line up, push the light bulb into the assembly until seated flush, then turn the bulb clockwise 1?4 turn.
  4. Plug the electrical light bulb wiring harness into the new light bulb. Install any items removed from the engine compartment.
PREMIER AND MONACO Unlike the other vehicles covered by this manual, the removal and installation of the headlamp bulbs in the Premier and Monaco models requires the extraction of the entire headlamp lens assembly.
  1. Remove the grille-to-headlamp assembly attaching screws.
  2. Disconnect the headlamp aiming cable from the aiming screw end.
  3. Remove the headlamp assembly attaching bolts from above and behind the lamp assembly and separate the lamp assembly from the vehicle.
  4. Unplug the headlamp wire connector. NOTE: Do not touch the bulb with bare fingers or any possibly oily surface, since reduced bulb life may result!
  5. Rotate the socket counterclockwise 1?4 turn and pull the socket from the back of the lens assembly. Fig. 4: Remove the bezel retaining screws to loosen the headlamp assembly - Premier and Monaco 86726g91.gif
    Fig. 5: Detach the headlamp wire connector - Premier and Monaco 86726g92.gif
    Fig. 6: Once the headlamp assembly has been removed from the vehicle, the various light bulbs can easily be removed - Premier and Monaco 86726g93.gif
    To install:
  6. Wearing gloves or holding the replacement bulb with a cloth rag to keep oil off of the bulb surface, insert the bulb into the rear hole of the headlamp assembly. Make certain that the alignment grooves and tabs line up, push the light bulb into the assembly until seated flush, then turn the bulb clockwise 1?4 turn.
  7. Plug the headlamp wire connector back into the headlamp bulb.
  8. Install the assembly into the vehicle and secure in place with the mounting bolts.
  9. Connect the headlamp aiming cable to the aiming screw end.
  10. Install the grille-to-headlamp assembly attaching screws.
prev.gif next.gif

Oct 15, 2010 | 1991 Chrysler New Yorker

1 Answer

2007 Mercury Milan Premier V6 ac compressor clutch won't engage. Fuses and relays are ok. Pressure switch checks out ok. What could cause the problem?


you may need to top up the coolant,r112,r140or what ever the car is useing. if the car can'nt be topped up then you have a leak that needs to be fixed,usually the drier.

Oct 14, 2009 | 2007 Mercury Milan V6 AWD Sedan

3 Answers

Where are the headlight adjustment screws on a 2006 mercury milan?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 17, 2009 | 2006 Mercury Milan

1 Answer

1997 Mercury villager left headlight doesn't work.


go here. we can help you. Also, did you check the headlamp relay in the box under the hood? One relay is in box in front of battery, other is in narrow box along passenger side fender under the hood. swap left & rt headlamp relays to see if it changes.

http://groups.yahoo.com/group/villagerquest/

Jul 13, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...