Question about Cars & Trucks

Open Question

Lights low and high beam adjustment for rodeo ute 2005

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: low beam head lights won't work

Check your relay switches under the hood fuse box. They should be a light grey from factory, they are about 1 x 1" in size and there are a few in there. Pull one out at a time and if they look brownish or yellowing replace. Go to Napa or Auto Zone for $15.99 a peice that most likely will fix it.

Posted on Mar 24, 2009

  • 161 Answers

SOURCE: low beam light does not work only high beam works

double check the bulb. swap the two bulbs if it's only one side of low beams are out (to see if it's the bulb). also take a look at the wiring itself, including where the bulb plugs in, for corrosion or breakage.
if your serious about keeping this Z at stock shape, restoring it, or just keeping it running, you can get goodies for it at blackdragonauto.com

Posted on Jun 17, 2009

  • 1986 Answers

SOURCE: Replacing headlights and adjustment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

  • 7353 Answers

SOURCE: low beams don't work - both out at the same time.

DID YOU CHECK THE BULBS?

Posted on Nov 04, 2009

Testimonial: "spot on."

  • 3 Answers

SOURCE: low beam not working but high beam is-Pontiac Vibe 2005

I have heard it could be the Daylight Running Light module located under the dash above the brake pedal. The module controls both the daytime running lights and the low beam lights. The high beams are independent of this module.

I have the same problem. I am trying to buy a new module.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low beams don't work


Are you getting power in and out of the dimmer switch for both high and low circuits ?

Jan 23, 2013 | 1998 Isuzu Rodeo

1 Answer

Head lights aimed to high


Hello...

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 12, 2009 | 2005 Chevrolet Colorado

1 Answer

How do you adjust the low beams on a chevrolet 2005 mailib max


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 05, 2009 | 2005 Chevrolet Malibu

1 Answer

The low beams on my 2005 altima are to high i need information on how to adjust


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 05, 2009 | 2005 Nissan Altima

2 Answers

My low beam lights sometimes stop working i still have high beam and daylight runing lights after a while they come on.2009 elantra dealer can't find problem.


when the low beams quit try switching from high to low and back and see if low beams stay on, if they do it may be the dimmer switch, if that doesn't change anything suspect the headlight switch.

Sep 02, 2009 | 2009 Hyundai Elantra

2 Answers

Replace highbeam 1996 rodeo


LIGHTING Headlights REMOVAL & INSTALLATION Non-Aerodynamic
Fig. 1: Replacing a sealed beam headlamp

bd06397.gif
  1. Disconnect the negative battery cable.
  2. Remove the front grille and/or headlight bezel.
  3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
  4. Before installing, spray some silicone grease into the bulb socket.
  5. Connect the wiring and install the bulb.
  6. Install the retaining rim and grille.
  7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.
Aerodynamic

Fig. 2: Replacing a headlamp bulb

cf46ef4.gif

Jul 24, 2009 | 1996 Isuzu Rodeo

1 Answer

Replacing headlights and adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 02, 2009 | 2005 Chevrolet Monte Carlo

1 Answer

Hit a dog. headlight is out of adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Dec 31, 2008 | 2005 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...