Question about Cars & Trucks

Open Question

Which race meeting on Saturday is classed as the main meeting

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1987 chevy corvette rear end sways

Well its a american muscle car and no doubt the bushes are worn somewhere,its the drivers fault as a muscle car can only do straight lines ,and not bends like a europeon sports car and it looks like someone has tried to do the dreaded bends with a american car causing the bushes to wear out .boy do i love winding up you americans about this -----till i watched top gear last week and hey a new stingray out with rear wheel drive only but all new suspension in carbon fibre on a race track against a porsche with 4x4 and guess what the stingray won ,no sliding or anything in fact it was the porsche that was slipping .and its its 20.000 GBP cheaper than anything else near it mainly the F type jag ,but then your talking different class with a JAGUAR ,i know i have one

Feb 27, 2015 | 1987 Chevrolet Corvette

1 Answer

What does F-1 mean?

you will have to provide more information but in race circles it is formula one and is a class that race cars compete in.

Jan 21, 2015 | Cars & Trucks

1 Answer

39700110engine block number search

the 0010 @ the end indicates that your engine block is a 350 cid or 5.7 liter (it may also be a 327cid but most likely not) these blocks were usually high nickel blocks (better strength in the casting) It may or may not be a 4 bolt main. The only way to tell is to remove the oil pan and look at the main bearing caps. Yes this engine should be good to race with I've run almost all of my 10 years in racing with those engine blocks with great success.

Sep 08, 2014 | GMC Jimmy Cars & Trucks

1 Answer

Problems with suzuki

IF the suzy engine has variable valve control V VT or mivec or what ever it is for a suzy It will be a toss up but for my money I would pick the mitsi engine as they have been developed for off road racing

Mar 22, 2014 | 2005 Suzuki Swift

1 Answer

What would make the camshaft to break twice

Drag racing; fast starts and high heat are the top three. But misaligned bearings, plugged oil line are up there also.

Aug 12, 2011 | 1995 Mercedes-Benz C-Class

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata

Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

Replacing wheel barrings

Yes it matters, you got the formula right, but I looked up your car and found too many different bearings, but , if your front front wheel has 2 bearings, one inside and one outside, most hubs have a dust seal, I didn't see one on yours, it shows a shim on the inside, then the bearing, race, hub, race, bearing, shim, lock nut, pin, don't over tighten it, and don't forget to grease it up, with the grease in your palm, pack it in there, unless you have a greaser, not a gun. Hope this helps.

Apr 15, 2010 | 1987 Mercedes-Benz 300-Class

1 Answer

Accelerater problem 1997 Mecedes C 200 Elegance

hi,try to check the accelerator cable for free movement,or you may check the idle actuator spring or clean the idle actuator,ty

Mar 17, 2009 | 1997 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77947 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides